Cisco MDS 9700 Series User Manual

6 NA 1.0
Xbar MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 NA JAE222305VS
2 NA JAE2217096X
3 NA JAE222305V5
4 NA JAE2217096L
5 NA JAE2217096J
6 NA JAE222305V8
Step 12 (Optional) If the standby Supervisor-1 Module is not in the po wered-dn state, then put the standby Supervisor-1 Module
to out of service, using the out-of-service module slot command .
where a slot indicates the chassis slot number in which the standby supervisor module resides.
switch(config)# out-of-service module 6
Step 13 Physically replace the standby Supervisor-1 Module (slot 6) with the second Supervisor-4 Module. To replace the
supervisor module, follow the steps explained in the “Installing a Supervisor Module” section and the “Removing a
Supervisor Module” section.
The following message is displayed:
2019 Jun 25 15:21:13 switch %PLATFORM-2-SINGLE_EJECTOR_STAT_CHANGED: Ejector's status in slot 6 has
changed, Ejector is OPEN
2019 Jun 25 15:21:15 switch %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAE17440HVB)
After inserting the new standby Supervisor-4 Module, the following message is displayed:
2019 Jun 25 15:21:27 switch %PLATFORM-2-MODULE_EJECTOR_POLICY_ENABLED: All Ejectors closed for
module 6. Ejector based shutdown enabled
2019 Jun 25 15:21:27 switch %PLATFORM-2-MOD_DETECT: Module 6 detected (Serial number :unavailable)
Module-Type Supervisor Module-4 Model :unavailable
Step 14 Wait for approximately 20 minutes for the new Supervisor-4 Module to come up in the HA-standby state. Once the
standby supervisor module is in the HA-standby state, the supervisor Status LED will be green.
If you see the following failure message, ignore the message, the active Supervisor-4 Module will bring up the standby
Supervisor-4 Module to the HA-standby supervisor state in some time.
2019 Jun 25 15:36:45 switch %SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
The following message is displayed on the active Supervisor-4 Module:
2019 Jun 25 15:36:45 switch %USBHSD-STANDBY-2-MOUNT: logflash: online
2019 Jun 25 15:36:49 switch %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor
supervisor, starting...
2019 Jun 25 15:38:30 switch %PLATFORM-1-PFM_ALERT: Disabling ejector based shutdown on sup in slot
6
2019 Jun 25 15:39:38 switch %MODULE-5-STANDBY_SUP_OK: Supervisor 6 is standby
2019 Jun 25 15:39:39 switch %PLATFORM-1-PFM_ALERT: Enabling ejector based shutdown on sup in slot
5
Step 15 Reinstall the license files on the new Supervisor-4 Modules.
switch(config)# copy usb1:licenses_archive_file_name.tar bootflash:switch_license.tar
Copy progress 100% 10KB
Copy complete, now saving to disk (please wait)...
switch(config)# copy bootflash:switch_license.tar bootflash:switch_license.lic
Copy progress 100% 10KB
Cisco MDS 9700 Series Switches Hardware Installation Guide
129
Installing, Removing, and Verifying Field Replaceable Units
Performing a Nondisruptive Migration

Cisco MDS 9700 Series Specifications

General

Brand	Cisco
Model	MDS 9700 Series
Category	Switch
Language	English