Control Techniques Digitax ST - Page 183

Parameter
structure
Keypad and
display
Parameter x.00
Parameter
description format
Advanced parameter
descriptions
Serial comms
protocol
Electronic
nameplate
Performance
Menu 17
Digitax ST Advanced User Guide 183
Issue Number: 1 www.controltechniques.com
Defines the mode of operation (or protocol) for the on-board EIA-RS485 port.
For details of these modes, refer to Table 5-12 below.
Table 5-12 Serial modes - Pr 17.06
17.06 RS485 mode
Digitax ST Variant Plus
Coding
Bit SP FI DE Txt VM DP ND RA NC NV PT US RW BU PS
111
Range 0 to 255
Default 1
Update rate 4ms write
Mode Description
1
4-wire CT-ANSI Slave
The port is set to 1 start bit, 7 data bits, even parity and 1 stop bit.
2 Reserved
3 Reserved
4 Reserved
5
2-wire CT-ANSI Slave
The port is set to 1 start bit, 7 data bits, even parity and 1 stop bit.
6 User mode. 1 start bit, 7 data bits, EVEN parity, 1 stop bit (10 bits total)
7 User mode. 1 start bit, 8 data bits, EVEN parity, 1 stop bit (11 bits total)
8 User mode. 1 start bit, 8 data bits, NO parity, 1 stop bit (10 bits total)
9 Reserved
10 Reserved
11 Reserved
12 Reserved
13,43,73
4-wire Modbus RTU slave
The EIA-RS485 port is set for:
Mode 13: 1 start bit, 8 data bits, NO parity, 2 stop bits.
Mode 43: 1 start bit, 8 data bits, EVEN parity, 1 stop bit.
Mode 73: 1 start bit, 8 data bits, ODD parity, 1 stop bit.
14, 44, 74
4-wire Modbus ASCII slave
The EIA-RS485 is set for:
Mode 14: 1 start bit, 7 data bits, NO parity, 2 stop bits
Mode 44: 1 start bit, 7 data bits, EVEN parity, 1 stop bit
Mode 74: 1 start bit, 7 data bits, ODD parity, 1 stop bit
15, 45, 75
2-wire Modbus RTU slave
The EIA-RS485 port is set for:
Mode 15: 1 start bit, 8 data bits, NO parity, 2 stop bits.
Mode 45: 1 start bit, 8 data bits, EVEN parity, 1 stop bit.
Mode 75: 1 start bit, 8 data bits, ODD parity, 1 stop bit.
16, 46, 76
2-wire Modbus ASCII slave
The EIA-RS485 is set for:
Mode 16: 1 start bit, 7 data bits, NO parity, 2 stop bits
Mode 46: 1 start bit, 7 data bits, EVEN parity, 1 stop bit
Mode 76: 1 start bit, 7 data bits, ODD parity, 1 stop bit
17, 47, 77
4-wire Modbus RTU master
The EIA-RS485 port is set for:
Mode 17: 1 start bit, 8 data bits, NO parity, 2 stop bits.
Mode 47: 1 start bit, 8 data bits, EVEN parity, 1 stop bit.
Mode 77: 1 start bit, 8 data bits, ODD parity, 1 stop bit.
18, 48, 78
4-wire Modbus ASCII master
The EIA-RS485 is set for:
Mode 18: 1 start bit, 7 data bits, NO parity, 2 stop bits
Mode 48: 1 start bit, 7 data bits, EVEN parity, 1 stop bit
Mode 78: 1 start bit, 7 data bits, ODD parity, 1 stop bit
19, 49, 79
2-wire Modbus RTU master
The EIA-RS485 port is set for:
Mode 19: 1 start bit, 8 data bits, NO parity, 2 stop bits.
Mode 49: 1 start bit, 8 data bits, EVEN parity, 1 stop bit.
Mode 79: 1 start bit, 8 data bits, ODD parity, 1 stop bit.
20, 50, 80
2-wire Modbus ASCII master
The EIA-RS485 is set for:
Mode 20: 1 start bit, 7 data bits, NO parity, 2 stop bits
Mode 50: 1 start bit, 7 data bits, EVEN parity, 1 stop bit
Mode 80: 1 start bit, 7 data bits, ODD parity, 1 stop bit
25
Motion Processor CT-Sync Master
The baud rate is fixed at 896875bps
26
Motion Processor CT-Sync Slave
The baud rate is fixed at 896875bps