Control Techniques Digitax ST - Index

Digitax ST Advanced User Guide 221
Issue Number: 1 www.controltechniques.com
Index
Numerics
4 -20mA .................................................................................103
A
AC_VOLTAGE_MAX ..............................................................16
AC_VOLTAGE_SET_MAX ......................................................16
Acceleration ..............................................................................6
Acceleration rate selector
........................................................38
Access Level ...........................................................................11
Accuracy .................................................................................41
Active current
..........................................................................70
Advanced menus ......................................................................7
Advanced parameter descriptions ...........................................19
Alarm
.......................................................................................12
Analog I/O ...............................................................................99
Analog input 1 destination
.....................................................102
Analog input 1 level
...............................................................101
Analog input 2 destination .....................................................103
Analog input 2 level
...............................................................101
Analog input 2 mode
.............................................................102
Analog input 3 destination .....................................................104
Analog input 3 level ...............................................................101
Analog input 3 mode
.............................................................103
Analog output 1 mode ...........................................................104
Analog output 1 source .........................................................104
Analog output 2 mode
...........................................................105
Analog output 2 source .........................................................105
Analog reference 1
..................................................................31
Analog reference resolution ....................................................41
ANSI communications protocol .............................................210
Application menu 1
................................................................199
Application menu 2 ................................................................200
Application menu 3 ................................................................201
At speed
................................................................................123
Auto-reset attempts ...............................................................141
Auto-tune .................................................................................81
B
Bandwidth set-up ....................................................................48
Baud rate
...............................................................................146
Binary sum ............................................................................121
Bipolar reference enable
.........................................................27
Brake control function
...........................................................156
Braking IGBT active ..............................................................124
Braking resistor alarm
...........................................................124
Braking time
..........................................................................139
C
Catch a spinning motor ...........................................................90
Clock .......................................................................................88
Coding .....................................................................................15
Coiler/uncoiler mode
...............................................................72
Compliance angle set-up ........................................................48
Control word ............................................................................95
Current control
........................................................................68
Current controller Ki gain
.........................................................74
Current controller Kp gain
.......................................................73
Current limit
.............................................................................71
D
Damping factor ....................................................................... 49
DC bus voltage ................................................................. 16, 80
Deceleration ............................................................................. 6
Deceleration rate selector
....................................................... 39
Destinations ............................................................................ 17
Differential feedback gain ....................................................... 46
Digital I/O 1 output select
..................................................... 114
Digital I/O 1 source/destination ............................................. 113
Digital I/O 2 output select ..................................................... 114
Digital I/O 2 source/destination
............................................. 113
Digital I/O 3 output select ..................................................... 114
Digital I/O 3 source/destination ............................................. 113
Digital I/O read word
............................................................. 113
Digital input ........................................................................... 108
Digital input 4 destination
..................................................... 113
Digital input 5 destination
..................................................... 113
Digital input 6 destination ..................................................... 113
Digital input auto-selection disable
....................................... 115
Digital output
......................................................................... 108
Digital reference resolution ..................................................... 41
Digitax ST Base .................................................................... 182
Digitax ST EZMotion
............................................................. 194
Digitax ST Indexer ................................................................ 182
Digitax ST Plus ..................................................................... 182
Direction commanded
........................................................... 124
Direction running .................................................................. 124
Display
...................................................................................... 8
Display - special functions ...................................................... 12
Drive active ........................................................................... 123
Drive enable
......................................................................... 112
Drive healthy ......................................................................... 123
Drive reset ...................................................................... 12, 141
Drive warning
........................................................................ 125
DST-Keypad ............................................................................. 8
E
Edit mode ................................................................................. 9
Electronic nameplate
............................................................ 216
Encoder auto configuration enable
......................................... 60
Encoder comms baud rate ..................................................... 55
Encoder error detection level
.................................................. 58
Encoder filter
.......................................................................... 61
Encoder lines per revolution ................................................... 53
Encoder phase angle
.............................................................. 50
Encoder position
..................................................................... 52
Encoder supply voltage .......................................................... 55
Encoder type .......................................................................... 56
Energy meter
.......................................................................... 92
External trip .......................................................................... 141
F
Factory defaults ...................................................................... 14
Factory defaults - US .............................................................. 14
Field gain reduction
................................................................ 85
G
Gain select .............................................................................. 47