D-Link DGS-1510/ME Series - Page 78

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
74
ethernet_type - (Optional) Specifies the Ethernet type mask.
ip - Specifies this is a IPv4 mask.
vlan - (Optional) Specifies a VLAN mask. Only the last 12 bits of the mask will be considered.
<hex 0x0-0x0fff> -Enter the VLAN mask value here.
source_ip_mask - (Optional) Specifies a source IP address mask.
<netmask> - Enter the source IP address mask here.
destination_ip_mask - (Optional) Specifies a destination IP address mask.
<netmask> - Enter the destination IP address mask here.
dscp - (Optional) Specifies the DSCP mask.
icmp - (Optional) Specifies that the rule applies to ICMP traffic.
type - Specifies the type of ICMP traffic.
code - Specifies the code of ICMP traffic
igmp - (Optional) Specifies that the rule applies to IGMP traffic.
type - Specifies the type of IGMP traffic.
tcp - (Optional) Specifies that the rule applies to TCP traffic.
src_port_mask - (Optional) Specifies the TCP source port mask.
<hex 0x0-0xffff> - Enter the TCP source port mask here.
dst_port_mask - (Optional) Specifies the TCP destination port mask.
<hex 0x0-0xffff> - Enter the TCP destination port mask here.
flag_mask - (Optional) Specifies the TCP flag field mask.
all – Specifies that all the flags will be used for the TCP mask.
urg – (Optional) Specifies that the TCP flag field will be set to ‘urg’.
ack - (Optional) Specifies that the TCP flag field will be set to ‘ack’.
psh - (Optional) Specifies that the TCP flag field will be set to ‘psh’.
rst - (Optional) Specifies that the TCP flag field will be set to ‘rst’.
syn - (Optional) Specifies that the TCP flag field will be set to ‘syn’.
fin - (Optional) Specifies that the TCP flag field will be set to ‘fin’.
udp - (Optional) Specifies that the rule applies to UDP traffic.
src_port_mask - (Optional) Specifies the UDP source port mask.
<hex 0x0-0xffff> - Enter the UDP source port mask here.
dst_port_mask - (Optional) Specifies the UDP destination port mask.
<hex 0x0-0xffff> - Enter the UDP destination port mask here.
protocol_id_mask - (Optional) Specifies that the rule applies to IP protocol ID traffic.
<0x0-0xff> - Enter the protocol ID mask here.
user_define_mask - (Optional) Specifies that the rule applies to the IP protocol ID, and that the mask
option behind the IP header length is 4 bytes.
<hex 0x0-0xffffffff> - Enter a user-defined mask value here.
packet_content_mask - Specifies the packet content mask. Only one packet_content_mask profile can be
created.
offset_chunk_1 - (Optional) Specifies that the offset chunk 1 will be used.
<value 0-31> - Enter the offset chunk 1 value here. This value must be between 0 and 31.
<hex 0x0-0xffffffff> - Enter the offset chunk 1 mask here.
offset_chunk_2 - (Optional) Specifies that the offset chunk 2 will be used.
<value 0-31> - Enter the offset chunk 2 value here. This value must be between 0 and 31.
<hex 0x0-0xffffffff> - Enter the offset chunk 2 mask here.
offset_chunk_3 - (Optional) Specifies that the offset chunk 3 will be used.
<value 0-31> - Enter the offset chunk 3 value here. This value must be between 0 and 31.
<hex 0x0-0xffffffff> - Enter the offset chunk 3 mask here.
offset_chunk_4 - (Optional) Specifies that the offset chunk 4 will be used.
<value 0-31> - Enter the offset chunk 4 value here. This value must be between 0 and 31.