D-Link DSR-1000 - Page 223

223
付録D ログメッセージ
ログメッセージ 緊急度 ログメッセージ 緊急度
P2: sending unfragmented message. DEBUG Sending P1 response: ERROR ERROR
P1: Sending fragment. DEBUG
NULL request (or response) PDU or NULL context: ERROR ERROR
P1: Total TLS message size = (%d) DEBUG Expecting start packet, got something else: ERROR ERROR
P1: sending unfragmented message. DEBUG Protocol version mismatch: ERROR ERROR
peapFragFirstProcess: TLS record size to receive = (%d) DEBUG Processing PEAP message (from frag): ERROR ERROR
Setting version %d DEBUG Processing PEAP message: ERROR ERROR
PEAP pkt rcvd: data len=(%d) ags=(%d) version=(%d) DEBUG Processing PEAP message: ERROR ERROR
Got PEAP/Start packet. DEBUG Indicated length not valid: ERROR ERROR
Got rst fragment DEBUG Did not get Acknowledged result: ERROR ERROR
Got fragment (n) DEBUG Cannot understand AVP value: ERROR ERROR
Got last fragment DEBUG eapExtResp is NULL: ERROR ERROR
Got unfragmented message DEBUG eapWscCtxCreate: EAPAUTH_MALLOC failed. ERROR
Got frag ack. DEBUG eapWscProcess: umiIoctl req to WSC failed, status = %d ERROR
Ext AVP parsed: ags=(0x%x) DEBUG eapWscCheck: Invalid frame ERROR
Mandatory bit not set: WARNING DEBUG eapWscBuildReq: Invalid state %d ERROR
Ext AVP parsed: type=(%d) DEBUG eapWscProcessWscResp: Invalid data recd pData = %p,
dataLen"
ERROR
Ext AVP parsed: value=(%d) DEBUG Data received for invalid context, dropping it ERROR
Got PEAPv0 success! DEBUG eapWscProcessWscResp: Build Request failed ERROR
Got PEAPv0 failure! DEBUG eapWscProcessWscResp: Invalid state %d ERROR
pCtx NULL. DEBUG eapWscProcessWscResp: Message processing failed 0x%X ERROR
Authenticator response check: Error DEBUG eapWscProcessWscData: Invalid notication recd %d ERROR
Authenticator response check: Failed DEBUG unable to initialize MD5 ERROR
MS-CHAP2 Response AVP size = %u DEBUG MDString: adpDigestInit for md5 failed ERROR
Created EAP/MS-CHAP2 context: OK. DEBUG EAPAUTH_MALLOC failed. ERROR
pCtx NULL. DEBUG EAPAUTH_MALLOC failed. ERROR
Deleted EAP/MS-CHAPv2 context: OK DEBUG NULL context created: Error ERROR
Not authenticated yet. DEBUG NULL context received: Error ERROR
Authenticator response invalid DEBUG Authenticator ident invalid. ERROR
EAP-MS-CHAPv2 password changed. DEBUG Success request message invalid: Error ERROR
rcvd. opCode %d. DEBUG Plugin context is NULL ERROR
pCtx NULL. DEBUG Deriving implicit challenge: Error ERROR
TLS message len changed in the fragment, ignoring. DEBUG Generating NT response: Error ERROR
no data to send while fragment ack received. DEBUG NULL in/out bu󱐯er: Error ERROR
TLS handshake successful. DEBUG Incorrect vendor id. ERROR
Created EAP/TTLS context: OK DEBUG Allocating memory for outBu󱐯: ERROR ERROR
Deleted EAP/TTLS context: OK DEBUG AVP code not recognized ERROR
No more fragments in message. ERROR DEBUG EAPAUTH_MALLOC failed. ERROR
Upper EAP sent us: method state = %d; decision = %d DEBUG Converting password to unicode: Error ERROR
P2: sending fragment. DEBUG Generating password hash: Error. ERROR
P2 send unfragmented message. DEBUG Generating password hash hash: Error. ERROR
P1: sending fragment. DEBUG Generating master key: Error. ERROR
P1: sending unfragmented message. DEBUG Generating rst 16 bytes of session key: Error.n ERROR
\tTLSMsgLen = 0x%x DEBUG Generating second 16 bytes of session key: Error.n ERROR
Send req ptr = 0x%x; Send resp ptr = 0x%x DEBUG Converting password to unicode: Error ERROR
P2 decision=(%d); methodState=(%d) DEBUG Constructing failure response: ERROR ERROR
Default EAP: method state = %d; decision = %d DEBUG Error checking authenticator response. ERROR
TTLS pkt: data len=(%d) ags=(0x%x) DEBUG Error generating NT response. ERROR
Got start DEBUG
Username string more than 256 ASCII characters: ERROR ERROR
Got rst fragment (n). DEBUG Invalid Value-Size. ERROR
Got fragment (n). DEBUG Invalid MS-Length. Got (%d), expected (%d) ERROR
Got last fragment DEBUG Error constructing response. ERROR
Got unfragmented message. DEBUG Got type (%d), expecting (%d) ERROR
Got frag ack. DEBUG Cannot handle message; opCode = %d ERROR