D-Link DSR-250N - Page 247

Unified Services Router User Manual
245
%s%d: bad sequence number: %d,
expected: %d,
DEBUG
ifmedia_ioctl: no media found for 0x%x,
DEBUG
PPPIOCDETACH file->f_count=%d,
DEBUG
ifmedia_ioctl: switching %s to , dev-
>name
DEBUG
PPP: outbound frame not passed
DEBUG
ifmedia_match: multiple match for
DEBUG
PPP: VJ decompression error
DEBUG
<unknown type>
DEBUG
PPP: inbound frame not passed
DEBUG
desc->ifmt_string
DEBUG
PPP: reconstructed packet
DEBUG
mode %s, desc->ifmt_string
DEBUG
PPP: no memory for
DEBUG
<unknown subtype>
DEBUG
missed pkts %u..%u,
DEBUG
%s, desc->ifmt_string
DEBUG
%s: INC_USE_COUNT, now %d,
__FUNCTION__, mod_use_count \
DEBUG
%s%s, seen_option++ ? , : ,
DEBUG
%s: DEC_USE_COUNT, now %d,
__FUNCTION__, mod_use_count \
DEBUG
%s%s, seen_option++ ? , : ,
DEBUG
PPPOL2TP %s: _fmt,
DEBUG
%s, seen_option ? > :
DEBUG
PPPOL2TP: --> %s, __FUNCTION__)
DEBUG
%s: %s, dev->name, buf
DEBUG
PPPOL2TP: <-- %s, __FUNCTION__)
DEBUG
%s: no memory for sysctl table!,
__func__
DEBUG
%s: recv: , tunnel->name
DEBUG
%s: no memory for VAP name!,
__func__
DEBUG
%s: xmit:, session->name
DEBUG
%s: failed to register sysctls!, vap-
>iv_dev->name
DEBUG
%s: xmit:, session->name
DEBUG
%s: no memory for new proc entry
(%s)!, __func__,
DEBUG
%s: module use_count is %d,
__FUNCTION__, mod_use_count
DEBUG
%s: 0x%p len %u, tag, p, len
DEBUG
PPPOL2TP %s: _fmt,
DEBUG
%03d:, i
DEBUG
PPPOL2TP: --> %s, __FUNCTION__)
DEBUG
%02x, ((u_int8_t *)p)[i]
DEBUG
PPPOL2TP: <-- %s, __FUNCTION__)
DEBUG
first difference at byte %u, i
DEBUG
%s: recv: , tunnel->name
DEBUG
%s: , t->name
DEBUG
%s: xmit:, session->name
DEBUG
FAIL: ieee80211_crypto_newkey failed
DEBUG
%s: xmit:, session->name
DEBUG
FAIL: ieee80211_crypto_setkey failed
DEBUG
PPPOL2TP %s: _fmt,
DEBUG
FAIL: unable to allocate skbuff
DEBUG
PPPOL2TP: --> %s, __FUNCTION__)
DEBUG
FAIL: wep decap failed
DEBUG
PPPOL2TP: <-- %s, __FUNCTION__)
DEBUG
FAIL: decap botch; length mismatch
DEBUG
%s: recv: , tunnel->name
DEBUG
FAIL: decap botch; data does not
compare
DEBUG
%s: xmit:, session->name
DEBUG
FAIL: wep encap failed
DEBUG
%s: xmit:, session->name
DEBUG
FAIL: encap data length mismatch
DEBUG
IRQ 31 is triggered
DEBUG
FAIL: encrypt data does not compare
DEBUG
[%s:%d] , __func__, __LINE__\
DEBUG
PASS
DEBUG
\t[R%s %#0x %#0x 0x%08x%08x],
(status == ERROR ? # : ), page, addr,
(uint32_t)(*pValue >> 32),
(uint32_t)(*pValue & 0xffffffff)
DEBUG
%u of %u 802.11i WEP test vectors
passed, pass, total
DEBUG
\t[W%s %#0x %#0x 0x%08x%08x],
(status == ERROR ? # : ), page, addr,
(uint32_t)(value >> 32), (uint32_t)(value
& 0xffffffff)
DEBUG
%s: 0x%p len %u, tag, p, len
DEBUG
%s: mac_add
%02X:%02X:%02X:%02X:%02X:%02X,
dev->name, addr[0], addr[1], addr[2],
addr[3], addr[4], addr[5]
DEBUG
%03d:, i
DEBUG