D-Link DSR-250N - Page 265

Unified Services Router User Manual
263
0x%08x 0x%08x,
0x%08x 0x%08x 0x%08x 0x%08x,
DEBUG
ath_pci: 32-bit DMA not available
ERROR
sc_txq[%d] : , i
DEBUG
ath_pci: cannot reserve PCI memory
region
ERROR
tid %p pause %d : , tid, tid->paused
DEBUG
ath_pci: cannot remap PCI memory
region) ;
ERROR
%d: %p , j, tid->tx_buf[j]
DEBUG
ath_pci: no memory for device state
ERROR
%p , buf
DEBUG
%s: unable to attach hardware: '%s'
(HAL status %u),
ERROR
axq_q:
DEBUG
%s: HAL ABI mismatch;
ERROR
%s: unable to reset hardware; hal status
%u, __func__, status
DEBUG
%s: failed to allocate descriptors: %d,
ERROR
****ASSERTION HIT****
DEBUG
%s: unable to setup a beacon xmit
queue!,
ERROR
MacAddr=%s,
DEBUG
%s: unable to setup CAB xmit queue!,
ERROR
TxBufIdx=%d, i
DEBUG
%s: unable to setup xmit queue for %s
traffic!,
ERROR
Tid=%d, tidno
DEBUG
%s: unable to register device, dev-
>name
ERROR
AthBuf=%p, tid->tx_buf[i]
DEBUG
%s: autocreation of VAP failed: %d,
ERROR
%s: unable to reset hardware; hal status
%u,
DEBUG
ath_dev_probe: no memory for device
state
ERROR
%s: unable to reset hardware; hal status
%u,
DEBUG
kdot11RogueAPEnable called with
NULL argument.
ERROR
%s: unable to start recv logic,
DEBUG
kdot11RogueAPEnable: can not add
more interfaces
ERROR
_fmt, __VA_ARGS__ \
DEBUG
kdot11RogueAPGetState called with
NULL argument.
ERROR
sample_pri=%d is a multiple of
refpri=%d, sample_pri, refpri
DEBUG
kdot11RogueAPDisable called with
NULL argument.
ERROR
===========ft-
>ft_numfilters=%u===========, ft-
>ft_numfilters
DEBUG
%s: SKB does not exist.,
__FUNCTION__
ERROR
filter[%d] filterID = %d
rf_numpulses=%u; rf->rf_minpri=%u; rf-
>rf_maxpri=%u; rf->rf_threshold=%u; rf-
>rf_filterlen=%u; rf->rf_mindur=%u; rf-
>rf_maxdur=%u,j, rf->rf_pulseid,
DEBUG
%s: recvd invalid skb
ERROR
NOL
DEBUG
unable to register KIFDEV to UMI
ERROR
WARNING!!! 10 minute CAC period as
channel is a weather radar channel
DEBUG
The system is going to factory
defaults........!!!
CRITICAL
%s disable detects, __func__
DEBUG
%s, msg
CRITICAL
%s enable detects, __func__
DEBUG
%02x, *(data + i)
CRITICAL
%s disable FFT val=0x%x , __func__,
val
DEBUG
Inside crypt_open in driver ######
CRITICAL
%s enable FFT val=0x%x , __func__,
val
DEBUG
Inside crypt_release in driver ######
CRITICAL
%s debug level now = 0x%x , __func__,
dfs_debug_level
DEBUG
Inside crypt_init module in driver
@@@@@@@@
CRITICAL
RateTable:%d, maxvalidrate:%d,
ratemax:%d, pRc->rateTableSize,k,pRc-
>rateMaxPhy
DEBUG
Inside crypt_cleanup module in driver
@@@@@@@@
CRITICAL
%s: txRate value of 0x%x is bad.,
__FUNCTION__, txRate
DEBUG
SKB is null : %p ,skb
CRITICAL
Valid Rate Table:-
DEBUG
DST is null : %p ,dst
CRITICAL