EasyManuals Logo
Home>Danfoss>DC Drives>VLT 2800

Danfoss VLT 2800 Design Guide

Danfoss VLT 2800
162 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #148 background imageLoading...
Page #148 background image
5.4 Mains Supply
5.4.1 Mains Supply 1x220-240 V/3x200-240 V
According to international
standards
Type 2803 2805 2807 2811 2815 2822 2822
PD2
2840 2840 PD2
Output current I
INV.
[A] 2.2 3.2 4.2 6.0 6.8 9.6 9.6 16 16
(3x200-240V)
I
MAX
(60 s) [A] 3.5 5.1 6.7 9.6 10.8 15.3 10.6 25.6 17.6
Output power
(230 V)
S
INV.
[KVA] 0.9 1.3 1.7 2.4 2.7 3.8 3.8 6.4 6.4
Typical shaft
output
P
M,N
[kW] 0.37 0.55 0.75 1.1 1.5 2.2 2.2 3.7 3.7
Typical shaft
output
P
M,N
[HP] 0.5 0.75 1.0 1.5 2.0 3.0 3.0 5.0 5.0
Max. cable
cross-section,
motor
[mm
2
/AWG]
1)
4/10 4/10 4/10 4/10 4/10 4/10 4/10 4/10 16/6
Input current I
L,N
[A] 5.9 8.3 10.6 14.5 15.2 - 22.0 - 31.0
(1x220-240 V) I
L,MAX
(60 s) [A] 9.4 13.3 16.7 23.2 24.3 - 24.3 - 34.5
Input current I
L,N
[A] 2.9 4.0 5.1 7.0 7.6 8.8 8.8 14.7 14.7
(3x200-240 V) I
L,MAX
(60s) [A] 4.6 6.4 8.2 11.2 12.2 14.1 9.7 23.5 16.2
Maximum cable
cross-section,
power
[mm
2
/AWG]
1)
4/10 4/10 4/10 4/10 4/10 4/10 4/10 4/10 16/6
Maximum pre-
fuses
IEC/UL
2)
[A]
20/2
0
20/20 20/20 20/20 20/20 20/2
0
35/35 25/25 50/50
Efficiency
3)
[%] 95 95 95 95 95 95 95 95 95
Power loss at
100% load
[W] 24 35 48 69 94 125 125 231 231
Weight [kg] 2.0 2.0 2.0 2.0 2.0 3,7 6.0 6.0 18.50
Enclosure
4)
type IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20/
NEMA 1
Table 5.13 Mains Supply 1x220-240 V/3x200-240 V
1) American wire Gauge. Maximum cable cross-section is the largest cable cross section that can be attached to the terminals. Always observe
national and local regulations.
2) Use Type gG pre-fuses for installation according to IEC rules. To maintain UL/cUL, use pre-fuses of the type Bussmann KTN-R 200 V, KTS-R 500 V
or Ferraz Shawmut, type ATMR (maximum 30 A). Place the fuses for protection in a circuit that is capable of supplying a maximum of 100,000
amps RMS (symmetrical), 500 V maximum.
3) Measured using a 25 m screened/armoured motor cable with a rated load and rated frequency.
4) IP20 is standard for VLT 2805-2875, whereas NEMA 1 is an option.
All about VLT 2800 Design Guide
146 Danfoss A/S © Rev. May/2014 All rights reserved. MG27E402
55

Table of Contents

Other manuals for Danfoss VLT 2800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Danfoss VLT 2800 and is the answer not in the manual?

Danfoss VLT 2800 Specifications

General IconGeneral
BrandDanfoss
ModelVLT 2800
CategoryDC Drives
LanguageEnglish

Related product manuals