Delphi Multec 3.5 User Manual

Index Multec 3.5 Fuel Injector Application Manual
11-4
Delphi Energy and Chassis Systems
Revision: 11/05-1
DFMEA ................................................................9-1
Diagnostic Trouble Code......................................6-9
Diagnostics ................................................. 3-3, 5-17
Direct injection .....................................................2-8
Director.................................................................3-1
Distribution
Air/EGR/PCV.................................................2-27
Document Management........................................1-1
Document Release and Updates ...........................1-1
Document Revision Procedure .............................1-1
Driveability Index Fuel Sensitivity............. 2-13, 8-4
Driver Characteristics.........................................3-28
Driver Circuit Clamping Voltage .......................3-13
Dry coil.................................................................2-9
Dual Spray Injector............................ 3-6, 3-11, 3-22
Durability...................................................... 7-2, 9-4
Durability Testing......................................... 8-1, 9-1
Dust ......................................................................7-3
DV
90
......................................................................
3-24
Dynamic minimum operating voltage ................3-12
Dynamic or Static Fuel Flow Specifications ......3-37
Dynamic Vehicle Testing .....................................8-2
Dynamometer Testing ..........................................8-1
E
ECM ...................................................................5-17
ECT ...................... See Engine Coolant Temperature
Electrical Continuity.............................................6-9
Electrical Interface................................................4-9
Electrical Specifications ............................. 1-3, 3-38
Electromagnetic Compatibility.............................4-9
EMI............................................................. 3-13, 4-9
Emission Requirements ......................................2-23
Emissions, Evaporative ......................................2-25
Emissions, exhaust ...............................................8-3
Engine Combustion Fundamentals.......................2-2
Engine Controller ....................................... 1-2, 4-14
Engine Controller Software................................2-27
Engine Coolant Temperature..............................5-11
Engine horsepower .............................................3-14
Engine Intake Manifold Pressure .......................3-40
Engine Misfire Diagnostics ................................5-18
Engine Protection ...............................................5-13
Engine Software .................................................2-24
Engine Starting Conditions.................................5-13
Engine Underhood Environment........................2-14
Engine Vacuum ..................................................2-26
Environmental Conditions..................................3-39
EPA Vehicle Emissions Information....................1-6
Equivalence Ratio.................................................2-4
Evaporative Canister .................................. 2-9, 2-21
Exterior Outline....................................................3-3
External Exposure ................................................7-3
F
Face seal .............................................. 3-2, 3-8, 6-11
Fail Soft (Limp Home) .......................................5-14
Federal Emissions Test Procedure........................2-8
Filter
Chassis...................................................... 1-2, 7-4
Fuel Inlet.........................................................3-36
Filtration .............................................................3-36
Flow Characterization ........................................2-27
Fuel
Alcohol blends........................................ 3-12, 7-3
Composition ...................................................2-10
Gasoline......................................... 2-10, 2-11, 7-3
High Aromatic..................................................7-3
Oxygenated............................................. 2-3, 2-10
Peroxide - Test..................................................7-3
Fuel Compatibility..............................................3-40
Fuel Flow
Considerations ................................................2-20
Requirements....................................................1-2
Fuel Injection Timing .........................................5-15
Fuel Injector
Design Effects on Evaporative Emissions......2-25
Tester, Tool J-39021.......................................6-11
Fuel Lubricity .....................................................3-28
Fuel Particles ........................................................2-7
Fuel Pressure ..................................... 3-1, 3-13, 3-40
Regulated........................................................2-21
Regulator ....................................... 1-2, 2-22, 2-23
Regulator Flow Rate.......................................2-21
Relief ................................................................6-9
System .................................................. 3-28, 5-19
Fuel Pump..................... 2-19, 2-20, 2-22, 2-27, 5-17
Fuel Pump Correction.........................................5-14
Fuel Pump Output - Nominal .............................2-21
Fuel Rail ...............................................................1-2
Fuel Spray Characteristics ....................................2-7
Fuel system capacity...........................................5-19
Fuel Tank............................................................2-26
Fuel Temperature................................................3-40
Fuel Trim Diagnostics ........................................5-17
Fuel Volatility.....................................................2-26
Full Recirculating Systems.................................2-21
G
Gain Consideration.............................................5-19
Gas Line Anti-Freeze ...........................................7-3
General Description - Injector ..............................3-1
Government Documents .......................................1-5
Government Regulations ....................................2-25
H
Handling Procedures ............................................6-1
High Transient Conditions ...................................2-9

Delphi Multec 3.5 Specifications

General

Brand	Delphi
Model	Multec 3.5
Category	Laboratory Equipment
Language	English