Delphi Multec 3.5 User Manual

Multec 3.5 Fuel Injector Application Manual Index
Delphi Energy and Chassis Systems
Revision: 11/05-1 11-5
Hot Fuel Handling .............................2-14, 3-22, 8-2
How this Manual is Arranged...............................1-2
Humidity.............................................................3-40
Hydrocarbons .....................................................2-10
Hydro-lock............................................................7-6
I
IAT ................................See Intake Air Temperature
Identification and Markings .................................3-5
Impact...................................................................6-3
Inductance ..........................................................3-39
Industry Documents..............................................1-6
Injection Methods.................................................5-2
Injection timing ..................................................3-23
Injector................................................................5-17
Absolute Operating Pressure ..........................2-19
Balance Test ...................................................6-11
Body Temperature ..........................................3-28
Cone Angle.....................................................3-21
Controls ..........................................................3-12
Design..................................................... 2-25, 3-8
Driver Diagnostics..........................................5-18
Intercept..........................................................2-27
Offset ................................................................5-7
Operating Temperature.....................................7-1
Part-to-Part Tolerances...................................3-28
Placement .......................................................3-21
Retaining Clip...................................................3-6
Sensitivity .......................................................5-19
Slope.............................................. 2-27, 5-6, 5-10
Spray.................................................................1-2
Targeting ......................................... 1-2, 3-1, 3-21
Temperature....................................................5-19
Tip Leakage....................................................2-25
Injector Flow
Calibration ......................................................3-28
Characterization...................................... 2-27, 5-1
Rate...................................................................7-2
Sizing..............................................................3-13
Tolerances.......................................................2-20
Installation on the Engine.....................................6-5
Intake Air Temperature ......................................5-11
Integral Correction..............................................5-15
Interchangeability ...............................................6-11
Interface
Electrical...........................................................1-3
Mechanical ...............................................1-3, 4-3
System ..............................................................4-1
Interface Control Document .................................4-2
Internal Components ............................................3-5
Internal Injector Friction.....................................3-28
Introduction ..........................................................1-1
Isopropyl Alcohol.................................................7-3
L
Lambda.................................................................2-4
Leak
Testing ..............................................................6-6
Vacuum...........................................................5-17
Lean Mixtures.......................................................2-6
Limit testing........................................................5-15
Linear and Working Flow Range .......................3-31
Locating the Fuel Injector ....................................4-3
Low Battery Voltage Conditions........................3-12
Low Pulse-Width
Correction.................................2-28, 5-5, 5-7, 5-9
Fueling Accuracy..............................................8-4
Repeatability...................................................3-32
Low Voltage Correction .......................................5-8
Lubricants
Seal-ring ...........................................................6-8
Lubrication ...........................................................6-5
M
Magnetic circuit.......................................... 3-8, 3-37
Magnetic Field......................................................3-1
Maintenance, Service and Repair .........................6-9
Make-up pulses...................................................3-15
Malfunction Indicator Lamp..................... 5-17, 5-18
Manifold Absolute Pressure (MAP) 5-11, 5-17, 5-19
Manifold Pressure Sensitivity...............................8-5
Manifold Vacuum.................................................3-1
Mass - Injector......................................................3-5
Mass Air Flow System ......................2-14, 2-19, 5-2
Maximum Current ..............................................3-12
Maximum Fuel Pressure.......................................7-5
Maximum Power Fueling Requirements ............2-19
Mechanical Integrity.............................................9-4
Metri-Pack ..........................................................4-11
Minimum fuel flow................................... 3-15, 3-18
Minimum Fuel Pump Flow Output.....................2-21
Minimum Operating Voltage (MOV)....... 2-19, 3-12
Minimum Pulse-Width (MPW)........... 3-28, 5-6, 5-8
Mixture motion control devices..........................3-23
Moisture................................................................6-3
Molecular Weight Constituents ..........................2-10
Monte Carlo Analysis.........................................3-35
Movement Within the Plant..................................6-4
MPFI Fuel Rail Assembly ..................................2-21
Multec 3.5 Fuel Injector .......................................2-1
N
Nitrogen (NOx) Emissions ...................................2-6
Noise...................................................................3-38
O
O2 Sensor ...........................................................5-17
OBD II................................................................5-17

Delphi Multec 3.5 Specifications

General

Brand	Delphi
Model	Multec 3.5
Category	Laboratory Equipment
Language	English