Index Multec 3.5 Fuel Injector Application Manual
11-6
Delphi Energy and Chassis Systems
Revision: 11/05-1
OBD-II Diagnostic Procedures.............................1-6
Objectives of this Manual.....................................1-1
Offset ............................................................ 5-5, 5-6
Olefins ................................................................2-12
Open Loop............................................................5-4
Opening response ...............................................3-27
Open-Loop.................................................... 5-2, 5-9
Order of Precedence .............................................1-5
orientation tab.......................................................4-4
Orienting the Injector ...........................................4-4
O-ring ...................................................See Seal-ring
Overpressurization................................................9-5
Oxygen sensor ............................................ 2-23, 4-8
Diagnostics .....................................................5-18
Oxygenated Fuels .................See Fuels: Oxygenated
Ozone....................................................................7-3
P
Packaging Methods ..............................................6-3
Packing Procedures ..............................................6-3
Paraffins..............................................................2-11
Particle Size and Injection Timing .......................2-8
Peak-and-hold........................................... 3-12, 4-14
Permeation.................................................. 2-25, 3-2
Physical Specifications................................. 1-3, 3-3
Piston Protection.................................................3-16
Plugging........................................................ 7-1, 7-4
Polarity ...............................................................4-10
Power enrichment............................ 2-19, 3-16, 5-11
Pressure ..............................................................3-40
Balance .............................................................6-9
Differential .....................................................5-10
Gain of System ...............................................5-19
Pressure Regulator......................2-1, 2-19, 2-21, 5-5
Pressure Regulator Gain/Considerations ............2-22
Prime Pulse................................................. 5-13, 7-6
Product Description, Fuel Injection......................3-1
Product Handling..................................................6-1
Production Limit Verification Tests .....................8-5
Proportional Correction ......................................5-14
Pulse-Width ................................................ 2-14, 5-5
Limits..............................................................3-27
Pulse-Width Modulation (PWM) .........................5-8
Purge Rates.........................................................5-19
Purge System............................................ 2-21, 5-17
PZEV .......................................................... 2-8, 2-18
Q
Quality/Reliability/Durability...............................9-1
R
Receiving and Storage..........................................6-4
Recommendations and Precautions ......................7-1
Reid Vapor Pressure...........................................2-15
Relative Humidity...............................................3-40
Replacement Techniques......................................6-9
Resistance................................................. 3-12, 3-39
Returnless fuel system.2-1, 2-16, 2-17, 2-21, 2-27, 2-
28, 5-6, 5-10
Rev Limiters .......................................................5-13
Rich Mixtures .......................................................2-5
Road Splash..........................................................4-3
S
SAE J1832............................ 1-6, 3-33, 5-9, 9-3, 9-4
SAE J-spray..........................................................1-6
Salt Spray ................................................... 3-40, 7-3
Saturated switch........................................ 3-12, 4-14
Sauter Mean Diameter........................................3-23
Scope of Document ..............................................1-1
Seal-ring ........................ 3-2, 3-7, 4-8, 6-1, 6-6, 6-10
Sequential Firing Scheme......................... 3-18, 3-38
Sequential Fuel Injection......................................5-3
Set Point Flow Shifts ............................................7-2
SFMEA......................................................... 1-5, 9-1
Shock .......................................................... 3-40, 9-5
Simultaneous Double Fire (SDF) .........................5-2
Simultaneous Single Fire (SSF) ...........................5-2
Single spray injectors .........................................3-22
Sizing Injectors - Flow .......................................2-18
Slope.....................................................................5-5
Software........................................................ 1-2, 5-1
Solenoid Coil........................................................3-1
Solenoid Coil Specifications ..............................3-38
Specific Component Technical Specification-Injector
.................................................................. 1-5, 9-6
Speed Density System ................................ 2-19, 5-1
Spray...................................................................5-19
Atomization ..................................... 2-7, 3-1, 3-23
Distribution.....................................................2-18
Effect on emissions...........................................8-3
Targeting ......................................... 3-11, 4-4, 8-3
Sta-Bil
...................................................................
7-6
Static flow rate....................................................3-37
Static minimum operating voltage......................3-12
Steady State Conditions......................................5-12
Steady State RPM Data ........................................4-6
Stoddard Solvent ........................................ 3-38, 7-3
Stoichiometric...............................2-3, 2-4, 2-10, 5-1
Storage..................................................................7-5
Sulfur ..................................................................2-12
Supply Lines.........................................................1-2
Support of Component After Sale ......................6-11
T
Tailbiting .................................................. 3-30, 3-31
Targeting ............................................................5-19
Temperature................................3-40, 5-19, 7-1, 9-3
Temperature Shock...............................................9-3
Terminal lubricant ............................................6-2, 7-7
To Next Page
Loading...
Need help?
General