Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifi cations
Setting items Setting contents
EQ Customize
Set so that unused equalizer
settings are not displayed
when [MULTEQ XT] is
pressed.
Equalizer settings for which
“Not Used” is set with the
Quick Select function cannot
be stored and called out.
Audyssey Byp. L/R : Set when not using the “Audyssey Byp L/R”
equalizer.
Used : Use.
Not Used : Do not use.
Set so that the “Audyssey Byp. L/R” settings can be made when the
Audyssey Auto Setup procedure is performed.
•
•
Audyssey Flat : Set when not using the “Audyssey Flat” equalizer.
Used : Use.
Not Used : Do not use.
Set so that the “Audyssey Flat” settings can be made when the
Audyssey Auto Setup procedure is performed.
•
•
Manual : Set when not using the “Manual” equalizer.
Used : Use.
Not Used : Do not use.
•
•
Making Detailed Settings (Manual Setup)
See overleaf
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confi rm the setting :Return to previous menu
Setting items Setting contents
Network Connecting
Make settings for wired
LAN.
q On the GUI menu, select “Network Connecting” – “Detail” and
press ENTER.
w Use o p to set “DHCP” to “OFF”, then press i.
The DHCP function is disabled.
e Use uip to input the address and press ENTER.
IP Address : Set the IP address within the ranges shown below.
The Network Audio function cannot be used if other IP addresses
are set.
CLASS A: 10.0.0.0 ~ 10.255.255.255
CLASS B: 172.16.0.0 ~ 172.31.255.255
CLASS C: 192.168.0.0 ~ 192.168.255.255
Subnet Mask : When connecting an xDSL modem or terminal
adapter directly to the AVR-4310CI, input the subnet mask
indicated in the documentation supplied by your provider. Normally
input 255.255.255.0.
Default Gateway : When connected to a gateway (router), input
its IP address.
Primary DNS, Secondary DNS : If there is only one DNS address
indicated in the documentation supplied by your provider, input it
at “Primary DNS”. If there are two or more DNS addresses, input
the fi rst one at “Secondary DNS”.
r Use i to select “Exit” and press ENTER.
Setup is complete.
When connecting to the network via a Proxy server, select “Proxy” and
press ENTER (vpage 40 “Proxy settings”).
If you are using a broadband router (DHCP function), there is no need
to make the settings at “IP Address” and “Proxy”, since the DHCP
function is set to “ON” in the AVR-4310CI’s default settings.
If the AVR-4310CI is being used connected to a network without the
DHCP function, the network settings must be made. In this case, some
knowledge of networks is required. For details, consult a network
administrator.
If you cannot connect to the Internet, recheck the connections and
settings (vpage 23).
If you do not understand about Internet connection, contact your ISP
(Internet Service Provider) or the store from which you purchased your
computer.
When you want to cancel the setting during IP address input, press
RETURN
.
•
•
•
•
b
•
•
•
•
•
Make network settings.
Setting items Setting contents
Network Connecting
Make settings for wired
LAN.
1. Connect the LAN cable (vpage 23 “Connecting to a Home Network
(LAN)”).
2. Turn on the AVR-4310CI (vpage 24 “Turning the Power On”).
AVR-4310CI performs automatic network setup due to the DHCP
function.
When connecting to a network that has no DHCP function, perform the
setting in step 3.
3. Set the IP address at the “Network Connecting”.
NETWORK CONNECTING
Exit
Detail
192.168.100.33
Set IP address and proxy manually
ONDHCP
IP Address
Enter
NETWORK CONNECTING
Proxy
Exit
192 . 168 . 100 . 033
Set IP address manually
OFFDHCP
IP Address
255 . 255 . 255 . 000Subnet Mask
000 . 000 . 000 . 000Default Gateway
000 . 000 . 000 . 000Primary DNS
000 . 000 . 000 . 000Secondary DNS
RETURN
Cancel
q
w
r e
Making the Network Settings (Network Setup)
Default settings are underlined.
Setting
1.AVR4310CIEU.indd 39 2009/04/14 16:37:09
To Next Page
Loading...
