Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifi cations
Setting items Setting contents
Rhapsody Account
Set or change Username
and Password (vpage 68
“Listening to Rhapsody“).
Username / Password
The types of characters that can be input are as shown below.
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSymbolsH ! # “ $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜ (Space)
GNumbersH 0123456789
You can change the character type when you press [SEARCH] or MENU
during character input.
The password may not contain underscores ( _ ).
•
•
Napster Account
Set or change Username
and Password (vpage 66
“Listening to Napster“).
Username / Password
The types of characters that can be input are as shown below.
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSymbolsH ! # “ $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜ (Space)
GNumbersH 0123456789
You can change the character type when you press [SEARCH] or MENU
during character input.
The password may not contain underscores ( _ ).
•
•
Network Information
Display network information.
Friendly Name / DHCP= ON/OFF / IP Address / MAC Address
Setting items Setting contents
Other
(Continued)
Party Start Level : Make settings for volume level when the Party Mode
is started.
Last : The same volume as set before the party mode was started.
– – – (0) : Always use the muting on condition when the Party Mode is
started.
–80dB ~ 18dB (1 ~ 99) : Start party mode with your preferred volume.
This can be set when “Party Mode Function“ is set to “ON“.
This is displayed from 0 to 99 when “Volume Display” (vpage 42) is
set to “Absolute”.
You can set to the upper limit set with “Volume Limit” (vpage 42) .
•
•
•
•
•
•
Network Status : Displays up to a maximum of 10 DENON products
connected on the same network.
Friendly Name / Model Name / Power ON/Standby / Select Source /
Volume Level / Party Mode status
“Network Status” is only displayed for DENON products supporting
the Network Status function.
•
Update Notifi cation : Displays a notifi cation message on the AVR-
4310CI’s GUI screen when the latest fi rmware is released with “Firmware
Update”. The notifi cation message is displayed for about 20 seconds
when the power is turned on. Connect to broadband Internet (vpage
23) when using this function.
ON : Display update message.
OFF : Do not display upgrade message.
When you press ENTER during display of the notifi cation message, the
“Check for Update” screen is displayed. (Refer to page 44 for more
information on “Firmware Update”)
Press RETURN to erase the notifi cation message.
•
•
•
•
Upgrade Notifi cation : Display a notifi cation message on the AVR-
4310CI’s GUI screen when downloadable fi rmware is released with “Add
New Feature”. The notifi cation message is displayed for about 20 seconds
when the power is turned on. Connect to broadband Internet (vpage 23)
when using this function.
ON : Display update message.
OFF : Do not display upgrade message.
When you press ENTER during display of the notifi cation message, the
“Add New Feature” screen is displayed. (Refer to page 45 for more
information on “Add New Feature”)
Press RETURN to erase the notifi cation message.
•
•
•
•
Making Detailed Settings (Manual Setup)
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confi rm the setting :Return to previous menu
Setting items Setting contents
Bass
Adjust low frequency range
(bass).
–10dB ~ +10dB (0dB)
Treble
Adjust high frequency range
(treble).
–10dB ~ +10dB (0dB)
HPF
Make settings for cutting
the low range to reduce
distortion in the bass.
OFF : The low range is not attenuated.
ON : The low range is attenuated.
Lch Level
Adjust the left channel
output level.
–12dB ~ +12dB (0dB)
The “Lch Level” can be set when “Channel“ (vpage 42) is set to
“Stereo“.
See overleaf
Set the audio to playback with multi-zone (ZONE2, ZONE3).
Making the Multi-zone Settings (Zone Setup)
Default settings are underlined.
Setting
1.AVR4310CIEU.indd 41 2009/04/14 16:37:12
To Next Page
Loading...
