ENGLISH
1.
Home Theater Playback - Playing
on
a Multi-channel System -
Auto
2Ch
Dolby Digital
Dolby Digital * 1
I
Dolby Digital Plus
Dolby Digital Plus * 1
Dolby TrueHD
Dolby TrueHD * 1
Multi LPCM
2-ch
Downmix
DTS
DTS*
1
LPCM
DTS-HD
DTS-HD*
1
...
".
LPCM
Multi LPCM
Dolby Digital
' Dolby Digital
LPCM Multi LPCM
2-ch
Downmix
Multi LPCM
LPCM
Dolby Digital
Dolby Digital
DVD-Video
';".f'
:-
DTS
DTS
"'I'L,
j
LPCM,
MPEG
2-ch LPCM
DVD-Aqdio
..:
LPCM. PPCM
I Multi LPCM
I~ownmix
:;.
"
,..~~
Multi
area
I
LPCM
Super audio
CD
*2
Stereo
area
.,.~
2-ch LPCM
CD
layer
i
I Dolby Digital
I
2-ch
Downmix
DivX®
.,
Dolby Digital i Multi LPCM
LPCM
:
------------
MP3, MP2
I
CD,
MP3,
WMA,
MC,
LPCM
2-ch LPCM
DTS-CD
DTS
Multi LPCM
2-ch
Downrr·ix
I LPCM
* 1 : Multi LPCM signals are output when "BD Audio
Mode"
is set to
"Mix
Audio
Output"
(GT' page
32)
Multi LPCM signals are output when outputting HDMI video signals with resolutions of 480i/576i or
480p/576p.
* 2 : Super Audio
CD
audio signals are output at 44.1
kHz
16-bit.
o Audio signal from the HOMI output terminal
You
can change the audio format and playback the number of channels according to the specifications
of the device to which the
DBP-A
1
OO's
HDMI audio output signals are input. Make settings while
checking the specifications of the audio device
to
be connected
as
well
as
the audio format/number
of
channels stored
in
media
and
files for playback.
Even
if "HDMI Setup" - "Audio Setup" on the
GUI
menu
is
set to "Auto" (GT'page
23),
multilinear
PCM
or
down
mixed 2-channel linear
peM
signals are output
if
a deVice that does not support bitstream IS
connected.
DBP-A
100 outputs a bitstream signal that
is
decoded by
the connected device.
'*
In
this case, you cannot make a speaker setting for
HDMI audio with the
DBP-A
100.
Make the setting with the connected device.
1
'*
When outputting Dolby TrueHD or DTS-HD audio, press
.
(~l
and set "BD Audio
Mode"
to "HD Audio Output"
(@,page32)
IDownmixed 2-channel Linear
PCM
audio signals
are
output
from the
DBP-A
100.
Make speaker settings with the connected
dev~
_
I Audio signal
are
not output from the
DBP-A
lOa's HDMI
Iterminal.
I Only video signals are output from the HDMI terminal.
'*
Make the audio connections.
2Ch
Mute
Devices with the following
built-in decoders
Dolby TrueHD
Dolby Digital Plus
Dolby Digital
DTS-HD
.
DTS
!
Devices compatible with
2-
i
channel HDMI audio input !
------------1-.----
i
i
Devices not compatible
with
HDMI audio signal
input
• When you press
(5
and set "HDMI Setup" - 'i'l.udio Setup" to 'i'l.uto" (GT'page 23) on the
GUI
menu.
the audio mode
is
set according to the connected device.
• When you want
to
set the HDMI audio
output
to one
of
your choosing change it according to the
following table.
• Refer to the owner's manual
of
the connected device for HDMI audio input specifications compatible
with the connected device.
Setting HOMI Audio Output
Outputs multi-channel Linear PCM audio signals with
Devices compatible with I Ispeaker settings by the
DBP-A
100.
multi-channel HDMI audio I Multi LPCM
'I'
'*
For
speaker settings,
on
the
GUI
menu, "Audio Setup"
input. but not capable
of
I
8M
On
-
"7.1
ch
Audio Out" - "Multi Channel" - "Speaker
speaker settings for each
II
I Configuration" (GT'page
25).
channel I
'*
BM : Bass Management (means multi-channel speaker
1----~--------1,-----____r
setting) 1
Devices compatible with
I'
Output
of
multi-channel Linear PCM audio signals from the
multi-channel HDMI audio Multi LPCM
DBP-A
100.
input. and capable of
8M
Off iMake speaker settings with the connected device.
speaker settings for each I
'*
BM : Bass Management (means multi-channel speaker
channel setting)
.~[.u.
• When the HDMI video resolution
is
set to
"1
080P24··. a HDMI video signal
is
output from the
DBP-A
100
with a resolution of 1080P and a frame rate of
24
frames per second, regardless of the video signal
on the disc being played. Because
of
this. when playing discs containing video signals recorded with
a frame rate of something other than
24
frames per second, the movement
of
the picture may
be
unnatural.
If
this happens, set the HDMI video resolution to something other than
"1
080P24".
• When the "I/P Direct" (GT'page
23)
setting
is
"On" and a disc with a frame rate
of
24 frames per second
is
played, no video signals are output from the video or S-Video outputs
• When the "liP Direct" (GT'page
23)
setting
is
"Off",
"1
080P24"
is
not displayed.
I
14
To Next Page
Loading...
Need help?
General
