ENGLISH
Audio
Setup
Setting
contents
[Default]
: Reset all distance settings to factory default.
Front
L /
Front
R / Center /
Subwoofer
/
Surround
L /
Surround
R /
Surr. Back L / Surr. Back
R : Select the speaker you want to set. and
set the distance. Set the value that is closest to the measured distance.
o- 60ft
or
0 - 18m
o
Distance:
Sets the distance between the listening position and each
speaker.
1feet]
or
[Meters]
: Set the unit
of
distance.
[Step]
: Set the minimum vanable width of the distance.
1ft, 0.1ft,
0.1
m,
0.01 m
Setting
items
7.1
ch
Audio
Out
Subwoofer
Mode
Sets the type of
low
frequency signal
to
be
output
from the subwoofer.
,
o Default
settings.
Front/Center/Subwoofer :
12
feet
(36
meters)
Surround/Surr.
Back·
10 feet (3.0 meters)
o Set the difference
in
the distance betweem the speakers to less than
20 feet (6.0 meters)
.~[.l'.
When "BD Audio
Mode"
is
set
to
"HD Audio Output"
(Gf'page
32). the
_____________
..::.i2istanc~~e.~tin2~s
(ji~b-'.e.d
during
DTS-HI?~2kH~~udio
p~yback
LEE
: Adds the
low
frequency signal of the channel for which the spea er
size
is
set to "small" to the
subwoofer
signal and outputs it.
LFE+Main : Adds the low frequency signal of
all
channels to the
subwoofer signal and outputs it.
Setting
contents
'N
l
n
4
o Select "Large" or "Small" not according
to
the physical size
of
the
speaker but according
to
the low frequency reproduction capabilities
based
on
the frequency set at "Crossover Freq."
o
On
the
GUI
menu. if the "Audio Setup" - "7.1-ch Audio
Out"-
"Multi
Channel" - "Speaker Configuration" item setting is changed. other
settings are automatically changed
as
well.
[Example]
If
you set "Front"
to
"Small", "Subwoofer" is set to "Yes" and "Large"
cannot
be
selected for "Center". "Surround" and "Surr. Back"
o Audio signal (sampling frequency. number of channels) from the
HDMI
output
terminal may be restricted by the specification
of
the
HDMI audio that
can
be input by the device
on
the other side.
[Example]
If the HDMI audio specification of the device on the other side
is 51-channel. even when
DBP-A
100 plays back
in
7.1-channel.
5.1-channel audio is output automatically.
In
that case. the analog
audio output becomes 5.1-channel output
as
well.
o Channel
Level:
Sets the volume of the test tone
to
be the same when
output from each speaker
[Mode]
: Select a test tone output method.
o
A.u.tQ
: Automatically switches the test tone output speaker
o
Manual:
Manually switches the test tone output speaker
[Start]
: Begins outputting the test tone
Front L /
Center
/
Front
R /
Surround
R /
Surr. Back R / Surr. Back L /
Surround
L /
Subwoofer
*When the test tone output stops. press
(5.
[SW
+10dB] : Increases the subwoofer output level by 10
dB.
*
o
Qff
: Does not change the subwoofer output level.
o
On:
Increases the subwoofer output level
by
+10
dB.
*:"SW +lOdB" cannot be set for "HDMI Setup"
~
'Audio Setup" -
"Multi LPCM BM On" - "Channel Level" on the
GUI
menu
[Default] : Resets all channel level settings to factory default.
o
No
: Does not Reset.
o
Yes:
Resets.
Setting
items
7.1·ch
Audio
Out
•
26
Remote
control
operation
buttons
SETUP
CD
Displays the menu
·Cancels the menu
.Moves the cursor
(Up/Down/Left/Right)
8
.Makes the setting
RETURN
o
:Returns to previous menu