ENGLISH
To
household
power
outlet
(AC
120
V 60
Hz)
,
Connect the included power cord to the
DBP-A
1
DO,
and
plug it into
an
AC
outlet.
Once Connections are Complete
__
J
Power cord
(included)
I Connecting the Power Cord
I
r
I
IIN,oM
I
I •
Be
sure
to
insert the power plug firmly. Incomplete connection results in noise.
1 _
o Ethernet cable (CAT·5 or greater recommended)
•
An
ethernet cable
is
not included
with
the
DBP-A
100.
• Use only shielded
STP
or
ScTP
LAN
cable which
is
available at retailer.
• We recommend a shielded straight cable (normal type) for Ethernet connections.
If you use the flat type or a non-shielded cable, the noise may adversely affect other devices.
o Internet Connection via Broadband
o Modem
A device that connects to the broadband and conducts communications on the Internet.
Some modems also incorporate a router.
System Reguirements
o Router
When using the
DBP-A
1
DO,
we
recommend a router with the following features.
• Built-in DHCP (Dynamic Host Configuration Protocol) server.
This function automatically assigns
an
IP
address on the
LAN.
• Built-in 1
OOBASE-TX
switch (built-in switching hub compatible
with
speeds upwards
of
100 Mbps)
5.
Using
BD·L1VE
function or updating the software version of DBp·A100
',,0
I
For
Internet connections, use
an
ISP
(Internet Service Provider) Ask your local dealer for details.
IN,OM
•Do not connect
an
ETHERNET
connector directly to the
LAN
port/Ethernet connector
on
your computer.
• It
is
necessary to subscribe to
an
ISP
in
order to connect
to
the Internet. If you already have a
broadband connection, there is no need to subscribe anew.
• The router you can use varies with the
ISP
For
more information, contact your
ISP
or
PC
dealer.
• DENON assumes no responsibility whatsoever for any communication errors or problems resulting
from customer's network environment or connected devices.
ITurning the Power On
Press the unit's
'6
or the remote control's
O.
The
power
turns on, and the
power
indicator lights green.
'·LOADING" appears on the display, and disc information
is
read.
*The "NO DISC" message is displayed if a disc
is
not loaded.
L0
..
--::-
.-
o
.;
0 0
(DBP-Al00)
-~
o 8
GD(KjOO
00()O
(Remote control
unit!
o Other
• The
DBP-A
100
can
use the DHCP function to automatically set up the network.
• When setting up your network manually, after subscribing to
an
ISP.
make the settings according
to
directions in "Network Setup" on the
GUI
menu
(~page
29).
• If you connect the
DBP-A
100 to a network without a DHCP function, conduct
IP
address and other
settings according to "Network Setup"
on
the
GUI
menu
(~page
29).
• The
DBP-A
100 does not support
PPPoE.
If you subscribe to a service that
is
set
with
PPPoE,
a
PPPoE-
compatible router
is
required.
• When setting up the network manually, consult with your network administrator for the settings to
make.
On
the
GUI
menu, when "Other Setup" - 'f'\uto Power Mode" - "On"
(~page
31). the following states are
maintained for about 30 minutes, and then the power
is
automatically turned to standby.
• Disc not loaded
• Playback has stopped
• Stopped due to resume function
o When power
is
switched to standby
~O··-
PCJto'IEllOR'
Press either C on the unit. or 0 on the remote control.
[Power indicator status
in
standby model
• Power Saving Standby: Off
• Normal
Standby:
Red
• Quick Start
Mode:
Red
IN'OM
During power standby, a slight amount of
power
is
consumed.
To
totally cut
off
the power, remove the
power
cord from the
power
outlet.
20
To Next Page
Loading...
Need help?
General
