The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
41
The Tariff
General Description
Here follows an example of an easy tariff that uses two Blocks to calculate two different tariff amounts.
In the subscribed example there are two tariffs that differ for the initial drop value distance (Parameter n. 11).
The Block 1 has been programmed with an Initial Drop Value distance of 1000, the Block 2 with a value distance
of 2000.
To pass from Block 1 to Block 2 must be pressed F2 button. To do it program the Parameter n. 13 of the Block
n. 1 with a value of 2 (setting value of 2 means > go to Block 2 ).
To go back to Block 1, set in Parameter n. 13 of Block 2 the value of 1.
With this procedure it is possible to move from Block 1 to Block 2 and change the bander value by pressing F2
button.
- Power on the taximeter. By default all the parameters programmed in Block 0 get loaded in the Working
Block.
- Press F1 button to pass in Hired position. Now Block 1 gets loaded in the Working Block updating the
changed parameters values (Parameter 11 = 0 > 11).
PS: The parameter 15 defi ne the start fare block. This is the block loaded when F1 button is pressed to pass from
For Hire to Hired position.
Working
Block
Param.001
.
.
.
.
.
Param.429
Working
Block
Param.001
.
.
P.340
.
Param.429
Working
Block
Param.001
.
.
.
.
Param.429
Working
Block
Param.001
.
P.340*
.
Param.429
Block 0
Param.001
.
.
.
.
Param.429
Easy
Tari!
Amount
Power
On
Power
On
Power
On
Final
Tari!
Amount
Complex
Tari!
Amount
*= Modifi ed Parameter
Block 0
P.001.
.
.
.
P.015=1
.
.
.
Param.429
Wk.Block
P.001.
.
.
.
P.015=1
.
.
.
Param.429
Block 1
P.001.
.
P.011=1000
.
P.013=2
.
.
.
Param.429
Wk.Block
P.001.
.
P.011=1000
.
P.013=2
.
.
.
Param.429
Block 2
P.001.
.
P.011=2000
.
P.013=2
.
.
.
Param.429
Wk.Block
P.001.
.
P.011=2000
.
P.013=2
.
.
.
Param.429
The taximeter calculates the tariff thanks to the interaction of 429 programmable parameters.
They work into a block. The X-One Android have 63 parameters blocks that can be programmed to gener-
ate even the most complex tariff. Two blocks are very particular:
Block 0 and the Working Block.
The Block 0 is the StartUp block that loads per default all the 429
parameters in the Working Block when the taximeter starts
up. In a simple tariff calculation is suffi cient to use only the
Block 0 to calculate the amount.
The “Working Block” (not visible by the user) is the opera-
tive block that makes the fi nal tariff calculation.
In a simple tariff, it is getting charged by Block 0 with his
429 default programmed parameters. It calculates the fi nal
amount.
To calculate a more complex tariff it is nec-
essary to use, in addition to Block 0 , other
programmed blocks of parameters.
Their content replace, at the programmed
event (Prog.Date, Key press F1, F2, F3 etc.),
the relevant parameters of the Working
Block.
Every new modifi ed parameter value in a
Block will replace the old one in the Working
Block updating the tariff.
Example
For Hire Hired Hired
To Next Page
Loading...