The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
52
113
Decrease unit-wai! ng-! me in Prog-Date 7 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 7 be decreased based on the
percentage (Q.109)?
No / Yes
114
Insert as " xed cost in Prog-Date 7 - When passing from HIRED to STOPPED in Prog-Date 7 should the parameter of Q.109 be inserted as a
fi xed cost ?
No / Yes
115
Insert as percentage in Prog-Date 7 - When passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted as
a percentage?
No / Yes
116
Insert as " xed cost in Prog-Date 7 with F2 - Passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted as
a fi xed cost pressing key F2?
No / Yes
117
Insert as percentage in Prog-Date 7 with F2 - Passing from Hired to Stopped in Prog-Date 7 should the parameter of Q.109 be inserted
as a percentage pressing F2?
No / Yes
PROG-DA TE N. 8
118
Block-number in Prog-Date 8 -The block number (absolute) to be used during the date and hour programmed in Prog-Date 8. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
119
Block-o# set in Prog-Date 8: the block offset (relative) to be used during the date and hour programmed in Prog-Date 8. The relative block
offset is the number of blocks to add to the current block number in order to obtain the new block number. The allowed value goes from
0 (min) to 62 (max).
0 - 62
120
Percentage or cost in Prog-Date 8. this is the percentage or the cost that will be applied during the date and time as programmed in
Prog-Date 8. The interpretation as a percentage or as a cost depends on questions Q.121 to Q.128. In case of percentage consider
Q.121 to Q.124, Q.126 and Q.128. Questions Q.125 and Q.127 should be answered with: NO. In case of cost consider Q.125 and
Q.127. Questions Q.121 to Q.124, Q.126 and Q.128 should be answered with: NO. The cost is given in the local currency with
an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point. The
percentage is given with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
121
Increase unit-cost in Prog-Date 8 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 8 be increased based on the percentage (Q.120)?
No / Yes
122
Increase ini! al-cost in Prog-Date 8 - Should the initial-cost (Q.11) in Prog-Date 8 be increased based on the percentage (Q.120)?
No / Yes
123
Decrease unit-distance in Prog-Date 8 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 8 be decreased based on the percentage
(Q.120)?
No / Yes
124
Decrease unit-wai! ng-! me in Prog-Date 8 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 8 be decreased based on the
percentage (Q.120)?
No / Yes
125
Insert as " xed cost in Prog-Date 8 - When passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be inserted
as a fi xed cost?
No / Yes
126
Insert as percentage in Prog-Date 8 - When passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be
inserted as a percentage?
No / Yes
127
Insert as " xed cost in Prog-Date 8 with F2 - Passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be
inserted as a fi xed cost pressing F2?
No / Yes
128
Insert as percentage in Prog-Date 8 with F2 - Passing from HIRED to STOPPED in Prog-Date 8 should the parameter of Q.120 be
inserted as a percentage pressing F2?
No / Yes
Prog-Dat e priority ManagemeNt
129
Priority of Prog-Date 1 (night-! me) - This is the number that corresponds with the priority that Prog-Date n. 1 has with respect to the
other Prog-Dates. The allowed number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same
number then those Prog-Dates have the same priority.
No / Yes
130
Priority of Prog-Date 2 (holiday-! me) - This is the number that corresponds with the priority that Prog-Date n. 2 has with respect to
the other Prog-Dates. The allowed number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same
number then those Prog-Dates have the same priority.
No / Yes
131
Priority of Prog-Date 3 -This is the number that corresponds with the priority that Prog-Date n. 3 has with respect to the other Prog-
Dates. The allowed number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then
those Prog-Dates have the same priority.
No / Yes
132
Priority of Prog-Date 4 -This is the number that corresponds with the priority that Prog-Date n. 4 has with respect to the other Prog-
Dates. The allowed number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then
those Prog-Dates have the same priority.
No / Yes
133
Priority of Prog-Date 5 - This is the number that corresponds with the priority that Prog-Date n. 5 has with respect to the other Prog-
Dates. The allowed number goes from: 8 (min. priority) to: 1 (max. priority). If two or more Prog-Dates have the same number then
those Prog-Dates have the same priority.
No / Yes
To Next Page
Loading...