DMP Electronics XR100 - User Codes; Adding User Codes

XR500/XR100 User’s Guide 33User Menu
User Codes
This option allows you to add, delete, or change a user code. You
PD\DOVRDVVLJQVSHFLÀF8VHU3URÀOHVWRLQGLYLGXDOXVHUV
1234 = User Number
34812 = User Code
89456 = PIN (XR500E Code Plus PIN systems only)
John Smith = User Name
   3URÀOH
User Number - Every user is numbered 1 through 9999. This
QXPEHULGHQWLÀHVWKHXVHUWRWKHV\VWHPDQGLVWUDQVPLWWHGWRWKH
central station when the user arms or disarms areas.
User Code - Each user also has a 3- to 6-digit number to 999999, to
enter into the keypad when arming or disarming the system. Only
4-digit user codes can be assigned to All/Perimeter, Home/Sleep/
Away, or Home/Sleep/Away with Guest system users.
Note: A User Code cannot begin with zero and 3-digit codes cannot
begin with 98.
)RU 8/LQVWDOODWLRQVDYRLGXVLQJ UHSHWLWLYH RUVHTXHQWLDO
FRGHV
PIN - In an XR500E Card Plus PIN system, each user is assigned
a unique PIN (up to 6 digits) to enter into the keypad after
presenting their card/proximity credential to the reader when
accessing system functions.
User Names - Each code may also be programmed with the user
name. You may enter up to 32 characters for the name. As needed,
refer to Appendix C for Entering User Names information.
User 3URÀOH7KHXVHULVDOVRDVVLJQHGD3URÀOHWRE\WKH
SHUVRQDGPLQLVWUDWLQJWKHV\VWHP7KHSURÀOHQXPEHUGHWHUPLQHV
the areas and functions the user can access.
Adding User Codes
1. Access the User Menu.
2. Press COMMAND until USER CODES? displays.
3. Press any Select key. The keypad displays
ADD DEL CHG BAT.
4. Select ADD or BAT (Batch) to add a new user code.
5. At the USER NUMBER: - option, enter a user number and
press COMMAND. The display changes to USER CODE: - .
Note: Do NOT program a code for user number 1 unless you
intend to use the Ambush function. See Ambush.
6. Enter a user code of 3 to 6 digits and press COMMAND. The
user enters this number to arm, disarm, etc. If using access
cards, present the card instead of entering a code. After
entering the code the keypad displays USER NUMBER ### as
the user name.
7. A 32-character name may be entered to identify the user.
Press any top row key to clear the current name. You may
then enter the new name. After entering the name press
COMMAND. See Entering Names in Appendix C.
 7KH GLVSOD\ FKDQJHV WR 352),/( 12 6HOHFW WKH SURÀOH
number to assign a set of authorized functions to the user
FRGHDVRXWOLQHGLQWKH3URÀOH7DEOHRQWKHSUHYLRXVSDJH
Note: On All/Perimeter or Home/Sleep/Away systems use the
GHIDXOWSURÀOHVWKURXJK)RU+RPH6OHHS$ZD\ZLWK*XHVW
V\VWHPVXVHWKHGHIDXOWSURÀOHVWKURXJKIRUWKHPDLQKRXVH
V\VWHP GHIDXOW SURÀOHV  IRU WKH *XHVW  KRXVH V\VWHP
DQGGHIDXOWSURÀOHVIRUWKH*XHVWKRXVHV\VWHP