Dover Wayne Select S1 - G.4 Pulse Output Menu

144 pages

To Next Page

To Previous Page

98 Dover Fueling Solutions W2940305 Rev 07 8/2019

This page intentionally left blank

Main Page

Table of Contents5
Introduction9
Dispensers Covered9
Model Description10
Model Designation Format11
Technical Information12
Site Design & Preparation15
Local, State, and Federal Codes15
Safety Precautions16
Ethanol and Bio-Diesel Installations17
DEF Installations17
Existing Installations17
Island Construction, Dispenser Anchoring, Piping, and Bollards18
Installation19
Equipment Inspection19
Typical Site Layout19
Electrical Wiring20
General20
Electrical Termination Descriptions - All Dispensers20
Electrical Termination Descriptions - Pulse Output Interface Option21
Circuit Breakers & Emergency Electrical Disconnect23
Grounding23
Wire Type24
Conduit24
Gasoline & Diesel Hose and Accessories Installation25
General25
Vapor Recovery Nozzles26
DEF Hose and Accessories Installation26
Nozzle26
Breakaway/Swivel26
Hose26
Sealant26
Start-Up27
Initial Checkout27
Configuring the Dispenser Software28
General28
Making Configuration Changes28
Configuration Start-Up (Units Without Price Displays)29
Configuration Start-Up (Units with Price Displays)30
Set the Pulse Output Resolution (Pulse Output Interface Option Only)34
Operating Units W/ Pulse Output I/F Option before Control System Is Operational36
Bleeding Product Lines37
Initial Delivery37
Meter Check (Calibration)38
General38
Accuracy Verification38
Calibration Procedure39
Voltage Test40
Complete Installation40
Complete Warranty Registration40
Operation41
Safety Items You Should Know41
Portable Tanks and Containers42
Health Note42
Dispenser Operation42
Displays43
Electromechanical Totalizer44
Restarting after Power Failure or Shutdown44
Cycling Power to Clear Faults44
Dispenser Statistics & Diagnostics45
General45
Password Protection46
Changing Your Passwords46
Viewing the Electronic Totalizers48
Maintenance51
Preventive Maintenance51
Strainer/Filter - Gasoline & Diesel Dispensers51
Strainer/Filter - DEF Dispensers52
Cleaning and Corrosion Prevention Instructions52
Meter Maintenance Issue52
How to Get Service on Your Pump52
Appendix A: Dimensions & Base Layouts53
Appendix B: Electrical Ratings & Wiring Diagram61
Electrical Ratings61
Wiring Diagram: All Models62
Appendix C: Pulse Output Interface63
Pulse Output Interface Wiring Diagram63
Pulse Output Interface Board Layout64
Appendix C: Dispenser Current Loop & T7 Payment Terminal Connections65
C.1 General65
C.2 General Notes65
C.3 Site Layouts66
Site Layout a66
Site Layout B67
Site Layout C68
Site Layout D69
Site Layout E70
Point-To-Point Dispenser to Fusion Forecourt Controller Wiring71
Point-To-Point Dispenser to Fusion UDB Replacement Wiring72
Point-To-Point Dispenser to Data Distribution Cabinet Wiring73
Wiring Using One Data Distribution Cabinet (up to 16 Dispensers)74
Wiring Using Two Data Distribution Cabinets (up to 24 Dispensers)75
Payment Terminal RS485 Wiring76
C.10 Ethernet Connection77
Appendix E: Dispenser Software Configuration, Statistics & Diagnostics79
General79
Entering Functions and Statistics79
IRC Commands80
Changing Subfunction Values81
Resetting Totals81
Exiting Functions82
Exiting Statistics82
Quick Exit from Functions or Statistics82
Pulse Output Interface Option Settings83
E.10 List of Statistics84
E.11 Meter Number Assignments85
E.12 Configuration Functions86
Appendix F: Local Authorize / Standalone Operation99
General99
Place Dispenser into Standalone Operation from Pulse Output100
Place Dispenser into Standalone Operation from Serial Mode101
Appendix G: Weights & Measures Mode103
General Information103
Upper Level Menu103
Unit of Measure Menu105
Pulse Output Menu106
Automatic Temperature Compensation (ATC) Menu107
Product Pressurization Menu108
Program Change Menu109
Meter Totals110
Metrological Settings Menu111
G.10 Metrological Configuration Parameter Definitions112
G.11 Automatic Temperature Compensation (ATC) Testing113
Appendix H: IX Fleet Fuel Control System115
General115
Power Requirements115
Ethernet Connection115
IX Fleet Board Setup119
Appendix J: Bezel Security121
General121
Secure Access Modes121
One-Shot Control121
Local Passcode Control121
Servterm Loading121
Function Settings121
Enabling Security Mode122
Clearing a Breach123
One-Shot Control Breach Clear123
Localized Control Breach Clear123
Maintenance/Service124
Maintenance with One-Shot Control124
Maintenance with Localized Control124
Testing the Switches125
Appendix K: T7 Receipt Printer127
General127
Description of Indicator Lights & Control Button128
Replace Paper129
Paper Jams132
Appendix L: Error Codes135
Appendix M: Internal Wiring & Connections139
Internal Wiring139
Internal Wiring - Ixfleet & Connectors140
Appendix N: Warranty Registration141
Warranty Registration Instructions141

Dover Wayne Select S1 - G.4 Pulse Output Menu

Table of Contents

Related product manuals