Elgo LIMAX33 CP-00 SERIES - 20 Cleaning; 21 Accessories

92 pages

Save Page as PDF

To Next Page

To Previous Page

Replacing Components

- 90 -

20 Cleaning

WARNING!

The device can only be cleaned with a damp cloth, do not use aggressive cleanser!

21 Accessories

Table 31: Accessories

Order Code

Description

LIMAX S-RMS

Magnetic tape mounting kit for rail mounting

AB20-80-10-1-R-D-15-BK80

Magnetic tape

LIMAX33 CP MW

Mounting angle

Main Page

Default Chapter3
- Table of Contents3
1 List of Figures5
2 List of Tables5
3 General7
- Information on the Safety Manual7
- References7
- Explanation of Symbols7
- Statement of Warranties9
- Demounting and Disposal9
4 Safety10
- General Causes of Risk10
- Personal Protective Equipment10
- Conventional Use11
5 Transport and Storage12
- Safety Instructions for Transport, Unpacking and Loading12
- Handling of Packaging Material12
- Inspection of Transport12
- Storage12
6 Product Features13
- Functional Principle13
7 Technical Data14
- Identification14
- Figure 3: Example of an Info Sheet for the Documentation of the Installation with a Specific System Configuration15
- Dimensions of LIMAC33 CP-0016
- Technical Data LIMAX33 CP-0017
8 Constraints for Use (Safety Requirements for Integration)18
- Figure 5: Values for L and R of Trip Coil21
9 Type Designation22
10 Installation and First Start-Up23
- Operating Area23
- Check of Safety Relevant Configuration24
- Mechanical Installation24
- Electrical Installation24
- Figure 6: View on the Top- and Bottom-Side of LIMAX33 CP-00 with Esgc25
- Table 1: Connections PIO and SCA-Cable26
- Table 3: Floor Sensor Plugs27
- Figure 8: Installation Circuit Diagram of LIMAX33 CP-00 (Maximum Configuration)28
- Figure 9: Installation Circuit Diagram of LIMAX33 CP-00 (Minimum Configuration)29
- Figure 10: One SR and One Door Side30
- Figure 12: Esgc Actuator Connected to a Blocking Device on the Speed Governor (Remote Tripping)31
11 Operation Modes and Commissioning33
- Operation Modes33
- Figure 13: Operation Modes Overview34
- Table 5: Safety Output States in Pre-Commissioning Mode (See also  13.4)35
- Table 6: Safety Output States in Teach Mode or Teach Auto Mode When Reference Positions Are Available36
- Manual Learning of the Floor Table40
- Figure 15: Canopen Learning of Double Sided Floors43
- Automatic Learning of the Floor Table44
- Figure 16: Flow of Events in Teach Mode Auto45
- Figure 17: Time-Saving Flow of Events in Teach Mode Auto47
- Figure 18: Automatic Learning of Double Sided Floors49
- Reentering of Teach Mode, Sub-Mode "Manual50
- Reentering of Teach Mode, Sub-Mode „Auto51
- Adjustments51
12 During Operation53
- Triggering the Safety Functions53
- The Error Level and Error Codes53
- Table 10: Error Codes54
- Table 11: Errors Concerning Nonvolatile Stored Data55
- The Fault Register56
- Testing of the OC- Relays56
- Testing of the Esgc-Actuator56
- LED Signals57
13 Safety Functions58
- Safety Function Configuration58
- Safety Functions after Commissioning58
- Table 14: Distance to Assumptive Buffer Dependent on Moving Direction and Mode60
- Figure 20: ETSL-Curves61
- Figure 21: Conditions for Door Bridging and UCM64
- Clearance66
- Table 15: OC Reaction if Position Is Higher than Upper Inspection Limit68
- Figure 23: Relations to the Lower Reference Position69
- Figure 24: Relations to the Upper Reference Positions70
- Safety Functions During Commissioning71
- Safety Functions before Commissioning72
14 Configured/Settable Parameter and Features73
- Configuration73
- Table 20: Configuration Parameter for ETSL-Curve74
- Table 22: Configuration Features for Safety Functions75
- Table 23: Dependency "Enabled Safety Functions" => Needed Actuators/Relay Contacts76
- Table 24: Behavior of UCM and Overspeed Final Tripping Dependent on the Concerning Configuration Features77
- Settable Parameters78
15 Initial and Annual Examination79
- System Restart79
- Magnetic Tape79
- Software Identification79
- Set of Configuration79
- Interference Suppression Measures79
- Verification of the Floor Table80
- Check of Safety Functions80
16 Functional Safety83
- Safety Parameters83
- Table 27: Safe Failure Fraction, HFT and Type of the Subsystems84
- Demands of en 61508-2, Annex D285
- Safety Requirements for the Integration of the System86
17 Disturbances87
- Fault Clearance87
18 Repairs / Maintenance88
19 Replacing Components89
- Replacing Magnetic Tapes89
- Replacing the LIMAX33 CP-0089
20 Cleaning90
21 Accessories90
22 Index92

Elgo LIMAX33 CP-00 SERIES - 20 Cleaning; 21 Accessories

Table of Contents

Related product manuals