EMC VNX Series

EMC
®
VNX
™
Procedure Generator
EMC CONFIDENTIAL version: 4.5
40 of 51
Blade 3 - port 1 (HBA 1) connected to SP B - port 1
# /nasmcd/sbin/t2tty -c 2 "fcp show" | egrep "HBA 0|HBA 1"FCP ONLINE HBA 0: ALPA 000001
WWN: 5006016044602075 QE8 4G
FCP scsi-0: HBA 0: ALPA 0000ef SP-a00: 50060160BCE02EA7 Class 3
FCP ONLINE HBA 1: ALPA 000001 WWN: 5006016144602075 QE8 4G
FCP scsi-16: HBA 1: ALPA 0000ef SP-b00: 50060160BCE02EA7 Class 3
# /nasmcd/sbin/t2tty -c 3 "fcp show" | egrep "HBA 0|HBA 1"FCP ONLINE HBA 0: ALPA 000001
WWN: 5006016844602075 QE8 4G
FCP scsi-0: HBA 0: ALPA 0000ef SP-a01: 50060160BCE02EA7 Class 3
FCP ONLINE HBA 1: ALPA 000001 WWN: 5006016944602075 QE8 4G
FCP scsi-16: HBA 1: ALPA 0000ef SP-b01: 50060160BCE02EA7 Class 32:
Example 2 shows the commands and output for Blade enclosure 0 in a gateway in a fabric-connect
configuration. With:
Blade 2 - port 0 (HBA 0) connected to SP A - port 0 and SP B - port 0
Blade 2 - port 1 (HBA 1) connected to SP A - port 1 and SP B - port 1
Blade 3 - port 0 (HBA 0) connected to SP A - port 0 and SP B - port 0
Blade 3 - port 1 (HBA 1) connected to SP A - port 1 and SP B - port 1
# /nasmcd/sbin/t2tty -c 2 "fcp show" | egrep "HBA 0|HBA 1"FCP ONLINE HBA 0: S_ID 014500
WWN: 5006016044602075 QE8 8G
FCP scsi-0: HBA 0: D_ID 043f00 SP-a00: 50060160BCE02EA7 Class 3
FCP scsi-16: HBA 0: D_ID 043b00 SP-b00: 50060160BCE02EA7 Class 3
FCP ONLINE HBA 1: S_ID 014700 WWN: 5006016144600544 QE8 8G
FCP scsi-32: HBA 1: D_ID 043900 SP-b01: 50060160BCE02EA7 Class 3
FCP scsi-48: HBA 1: D_ID 043d00 SP-a01: 50060160BCE02EA7 Class 3
# /nasmcd/sbin/t2tty -c 3 "fcp show" | egrep "HBA 0|HBA 1"FCP ONLINE HBA 0: S_ID 014300
WWN: 5006016844600544 QE8 8G
FCP scsi-0: HBA 0: D_ID 043f00 SP-a00: 50060160BCE02EA7 Class 3
FCP scsi-16: HBA 0: D_ID 043b00 SP-b00: 50060160BCE02EA7 Class 3
FCP ONLINE HBA 1: S_ID 014100 WWN: 5006016944600544 QE8 8G
FCP scsi-32: HBA 1: D_ID 043900 SP-b01: 50060160BCE02EA7 Class 3
FCP scsi-48: HBA 1: D_ID 043d00 SP-a01: 50060160BCE02EA7 Class 3
14. [ ] Enter the following command to assign a storage group to a specific HBA by creating an initiator
record. You must create an initiator record for each connection (physical or logical) from the Blade ports
(0 and 1) to the SP ports.
CAUTION: Before issuing the command, verify that the values used to create the new initiator
record contain the correct information for each connection. Incorrect information can cause a
misconfiguration of the initiator record.
Use the command below that best represents the system type:
 Use the following command for a VNX VG2 or VNX VG8 gateway:
# /nasmcd/sbin/navicli -h <SPA_IP_Address> storagegroup -setpath -o –gname
<StorageGroup_Name> -hbauid <Blade_Port_HBA_UID> -sp <SP_Letter> -spport
<SP_Port_Number> -ip <Host_IP_Address> -host <Hostname>
 Use the following command for all other VNX Unified or File systems: