Why are display values not plausible (linearization) on my Endress+Hauser Micropilot FMR20?
If the display values are not plausible (linearization), it may be because SmartBlue and Modbus are active simultaneously. Log off Modbus and disconnect, or log off SmartBlue and disconnect, as the connection via SmartBlue has priority.
What to do if linearized output value is not plausible in Endress+Hauser Measuring Instruments?
If the linearized output value is not plausible, check the linearization table and the vessel selection in the linearization module.
Why does my Endress+Hauser Measuring Instruments device measure incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, it could be due to a configuration error. You should check and correct the parameter configuration and carry out mapping.
Why is my Endress+Hauser Micropilot FMR20 device not visible in the live list?
Your Endress+Hauser Measuring Instruments device may not be visible in the live list because it is already connected with another smartphone/tablet. Only one point-to-point connection can be established between a sensor and a smartphone or tablet.
Why is my Endress+Hauser Micropilot FMR20 Measuring Instruments device visible in the live list but cannot be accessed via SmartBlue?
If your Endress+Hauser Measuring Instruments device is visible but inaccessible via SmartBlue, and you are using an Apple device, log in as a standard user. Enter the username "admin" and the initial password (device serial number), paying attention to lower/upper case.
How to fix Modbus communication not working on Endress+Hauser Micropilot FMR20 Measuring Instruments?
If Modbus communication isn't working on your Endress+Hauser Measuring Instruments device, check the following: * Ensure that the Modbus signals are connected correctly. * If an access code is activated, enter the access code.
What to do if my Endress+Hauser Measuring Instruments device cannot be operated via SmartBlue?
There are a few reasons why your Endress+Hauser Measuring Instruments device might not be operable via SmartBlue: * An incorrect password may have been entered. Ensure you enter the correct password. * The sensor temperature may be too high. If the ambient temperature results in an elevated sensor temperature of >60 °C (140 °F), Bluetooth communication may be disabled. Shield the device, isolate it, and cool it down if necessary.
General| Measuring Principle | FMCW Radar |
|---|---|
| Frequency | 80 GHz |
| Housing Material | Aluminum or Stainless Steel |
| Enclosure Rating | IP66/IP67 |
| Type | Radar Level Transmitter |
| Device Type | Radar Level Transmitter |
| Application | Liquids |
| Process Temperature | -40 to +60 °C (-40 to +140 °F) |
| Process Pressure | -1 to +3 bar (-14.5 to +43.5 psi) |
| Accuracy | ± 2 mm |
| Output Signal | 4-20 mA HART |
| Communication | HART |
| Approvals | ATEX, FM, CSA, IECEx |
Outlines qualifications for personnel involved in installation, commissioning, diagnostics, and maintenance.
Defines application, media, permitted measurements, and clarifies incorrect use.
Covers safe operation, unauthorized modifications, and repair guidelines.
Covers general conditions and types of installation for the device.
Lists essential checks after installation for device integrity and security.
Details how to connect the device for HART communication.
Lists checks to perform after electrical connection for proper installation.
Emphasizes performing post-installation and post-connection checks before commissioning.
Guides through commissioning using the SmartBlue app and its requirements.
Guides on configuring level measurement using operating software like SmartBlue.
Covers software locking and access code management for data security.
Provides a table of common errors, possible causes, and solutions.
Lists errors related to SmartBlue operation and their solutions.
To Next Page
