Need help?Do you have a question about the Endress+Hauser Micropilot FMR60B and is the answer not in the manual?
General| Brand | Endress+Hauser |
|---|---|
| Model | Micropilot FMR60B |
| Category | Measuring Instruments |
| Language | English |
Explains the content and scope of the operating instructions, covering the device lifecycle.
Defines safety symbols (DANGER, WARNING, CAUTION) and information graphics used.
Lists available document types like Technical Information (TI) and Safety Instructions (XA).
Lists registered trademarks associated with the device and its components.
Specifies qualifications and authorization needed for installation, commissioning, and maintenance.
Defines the device's purpose for continuous, non-contact level measurement.
Outlines safety measures for personnel working with the device, including PPE.
Ensures safe operation, covers device modifications, and repair requirements.
Details device security mechanisms and operator responsibilities for IT security.
Provides a diagram illustrating the main components of the Micropilot FMR60B.
Details checks required upon receiving the device, including order code and condition.
Describes methods for identifying the device, such as nameplate and online tools.
Specifies legally required and relevant information found on the device's nameplate.
Provides essential guidelines for mounting, emphasizing dry environments.
Details internal vessel fittings and avoiding interference echoes for optimal measurement.
Covers mounting procedures for different antenna types, including threaded connections.
Explains how to rotate the housing for optimal alignment and accessibility.
Lists essential checks to perform after the device has been mounted.
Details requirements for connecting the device, including securing the cover and potential equalization.
Provides instructions on connecting the device, including supply voltage and cable specifications.
Details the wiring process, including safety warnings and connection order.
Illustrates terminal assignments for single and dual compartment housings.
Explains how to maintain the IP protection class of the housing and cable entries.
Lists checks to perform after electrical connection, ensuring proper installation.
Lists various methods for operating and configuring the device.
Describes how to operate the device using the local display and its keys.
Explains how to access and configure the device using a web browser.
Details the requirements and steps for establishing a network connection.
Covers using tools like FieldCare and DeviceCare for device operation.
Describes FieldCare as an FDT-based plant asset management tool.
Introduces DeviceCare as a tool for connecting and configuring Endress+Hauser devices.
Details device description files (GSD, FDI, DTM) needed for system integration.
Explains the purpose and format of the Device Master File (GSD) for PROFINET.
Describes modules and data flow for cyclic data exchange with automation systems.
Explains the meaning of status codes (BAD, UNCERTAIN, GOOD) for device diagnostics.
Covers the device's support for S2 system redundancy for continuous operation.
Guides on establishing connections using FieldCare and DeviceCare via PROFINET or CDI.
Covers setting the device name and activating the default IP address.
Explains how to set the operating language on the local display, via tools, or web server.
Details device configuration steps, including level measurement setup.
Describes using the commissioning wizard for guided initial setup.
Explains how to check the active write protection status of the device.
Describes how to view measured values via the web server or application menu.
Guides on adjusting device settings to match specific process conditions.
Provides solutions for common issues like device not responding or display errors.
Troubleshooting steps for issues encountered when operating via the SmartBlue app.
Explains how diagnostic messages are displayed and interpreted.
Defines the meaning of status signals (F, C, S, M) for device operation states.
Details methods for resetting the device password or factory settings.
Information about the device's firmware versions and their validity.
Provides guidelines for cleaning the device exterior safely and effectively.
Recommendations for periodic replacement of process seals.
Covers the Endress+Hauser repair concept and safety for Ex-certified devices.
Information on identifying, ordering, and downloading instructions for spare parts.
Procedures for replacing device components, including data upload/download.
Details on how to return the device for repair or calibration.
Instructions for the proper disposal of the product according to WEEE directive.
Details on the 316L weather protection cover for dual compartment housings.
Details on the plastic weather protection cover for single compartment housings.
Information on the adjustable mounting bracket for wall or ceiling installation.
Specifications for straight and angled M12 sockets, including material and IP rating.
Information regarding the optional remote display FHX50B.
Details on the Field Xpert SMT70 tablet PC for device configuration.
Specifies input parameters like measured variable, measuring range, and media groups.
Lists the maximum measuring ranges for different antenna types and sizes.
Explains factors affecting usable measuring range and selection guidelines.
Details output specifications including PROFINET-APL and signal on alarm.
Specifies ambient temperature ranges, limits, and housing material effects.
Defines process pressure ranges and temperature dependencies based on seals and connections.
To Next Page
