To Next PageTo Next PageWhy is my Endress+Hauser Measuring Instruments device not responding via the SmartBlue app?
The device may not be responding because there is no Bluetooth connection. To resolve this, enable the Bluetooth function on your smartphone or tablet. Also, ensure that the device is not already connected to another smartphone or tablet.
How to fix write access to parameter not possible on Endress+Hauser Proline Promag W 800?
If write access to a parameter is not possible, it may be because hardware write protection is enabled. Check the user role, enter the correct customer-specific access code, or verify the hardware write protection via DIP switch.
Why is my Endress+Hauser Proline Promag W 800 Measuring Instruments measuring incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, it could be due to a configuration error or operation outside of the specified application limits. To resolve this: 1. Check and correct the parameter configuration. 2. Observe the limit values specified in the Technical Data.
Why is my Endress+Hauser Measuring Instruments device not responding via SmartBlue App?
If your Endress+Hauser Measuring Instruments device is not responding via the SmartBlue App, it may be due to the absence of a Bluetooth connection or because the device is already connected to another smartphone or tablet. Ensure that the Bluetooth function is enabled on your smartphone or tablet.
What to do if Endress+Hauser Proline Promag W 800 shows correct value on display but signal output is incorrect?
If your Endress+Hauser Measuring Instruments device shows the correct value on the local display but the signal output is incorrect (though within the valid range), it is likely due to a configuration error. Check and correct the parameter configuration.
Why do I have no write access to parameters on my Endress+Hauser Proline Promag W 800?
If you have no write access to parameters on your Endress+Hauser Measuring Instruments device, it may be because hardware write protection is enabled. To resolve this: * Check user role * Enter correct customer-specific access code * Check hardware write protection via DIP switch.
What to do if login via SmartBlue app is not possible for Endress+Hauser Measuring Instruments?
If you cannot log in via the SmartBlue app, and the device is being put into operation for the first time, enter the initial password (which is the device serial number) and then change it.
Why does the local display of my Endress+Hauser Proline Promag W 800 remain dark for longer than 5 seconds?
If the local display of your Endress+Hauser Measuring Instruments device remains dark for longer than 5 seconds when touched, it could be due to several reasons: * The supply voltage does not match the voltage specified on the nameplate. Apply the correct supply voltage. * The supply voltage has incorrect polarity. Correct the polarity. * The connecting cables are not connected correctly. Check the cable connection and correct if necessary. * No battery pack or buffer capacitor is inserted or connected. Insert or connect the battery pack or buffer capacitor. * The device is not powered from the mains. Touch the display for 5 seconds.
Why is my Endress+Hauser Proline Promag W 800 Measuring Instruments device measuring incorrectly?
If your Endress+Hauser Measuring Instruments device measures incorrectly, it may be due to a configuration error, or the device is being operated outside its intended application. To resolve this: 1. Check and correct the parameter configuration. 2. Observe the limit values specified in the 'Technical Data'.
What to do if Endress+Hauser Proline Promag W 800 Measuring Instruments device shows correct value on display, but signal output is incorrect?
If your Endress+Hauser Measuring Instruments device shows the correct value on the local display but the signal output is incorrect, even though it's within the valid range, it is likely due to parameterization errors. Check the parameterization and correct it as needed.
General| Device Type | Electromagnetic Flowmeter |
|---|---|
| Measurement Principle | Faraday's law of electromagnetic induction |
| Housing Material | Aluminum, stainless steel |
| Pressure Rating | Up to 40 bar |
| Output Signal | 4 to 20 mA HART, Modbus RS485, PROFIBUS DP, PROFINET |
| Power Supply | 24 V DC |
| Process Connection | Flange (EN, ASME, JIS) |
| Lining Material | PTFE, rubber |
| Electrode Material | 316L stainless steel, Hastelloy, titanium |
| Degree of Protection | IP67 |
