EDA 2530 Commissioning Procedure for Cable and Wireless Access
1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01
© Ericsson AB 2010
Commercial in confidence
183 (200)
MSAN EDA 2530 Commissioning
(3.5) Local Craft Terminal Configured satisfactory Y/N/NA
(4.3) Preliminary Checks satisfactory Y/N/NA
(4.4) Earthing & DC Supply Checks satisfactory Y/N/NA
Earth Resistance measurement, < 1ΩΩ
Supply 1 measurement (- 50 v) V dc
Supply 2 measurement (- 50 v) V dc
(4.5) Power Supply Connection Checks satisfactory Y/N/NA
(5.1) PC IP Address Configure satisfactory Y/N/NA
(5.2) Common Part Card CF Download satisfactory Y/N/NA
(5.3) Subrack Equipping satisfactory Y/N/NA
(5.4) Logon to EDA 2530 via LCT satisfactory Y/N/NA
(5.5) Reset Backplane EPROM satisfactory Y/N/NA
Configure Out Of Band IP Address satisfactory Y/N/NA
(5.6) Software Inventory Check satisfactory Y/N/NA
(6) Software Download/Upgrade satisfactory Y/N/NA
(7.1) Configure Opt SFP Modules satisfactory Y/N/NA
(7.2.1) Configure CP Port 1 satisfactory Y/N/NA
(7.2.2) Configure CP Port 2 satisfactory Y/N/NA
(7.2.3) Configure CP Port 3 satisfactory (If required) Y/N/NA
(7.2.4) Configure CP Port 4 satisfactory (If required) Y/N/NA
(7.3) Configure EDA2530 Tag protocol ID/Bridging satisfactory Y/N/NA
(7.4) ADSL Card Configuration Files available Y/N/NA
(7.5) SHDSL Card Configuration Files available Y/N/NA
(7.6) Configure Static VLANs satisfactory Y/N/NA
(7.7) Adding Interfaces to Static VLANs satisfactory Y/N/NA
(7.8) Configure the IBM Sub-Interface satisfactory Y/N/NA
(7.9) Assign the In Band Management IP Address satisfactory Y/N/NA
(7.10) Configure the Default Gateway satisfactory Y/N/NA
(7.11) xDSL Bridge management - Configure xDSL Bridge satisfactory Y/N/NA
(7.12) xDSL Bridge management - Configure PVC satisfactory Y/N/NA
(7.13) xDSL Bridge management - Configure Downstream Flow satisfactory Y/N/NA
(7.14) Configure ADSL Profiles satisfactory Y/N/NA
(7.15) Configure SHDSL Line Profiles satisfactory Y/N/NA
(7.16) Configure SHDSL Stack Profiles satisfactory Y/N/NA
(7.17) Configure POTS Card(s)
(7.17.1) POTS Card Configuration Files available Y/N/NA
(7.17.2) Step 1: Uninstall LCT/Java & reinstall LCT 07.02.05 satisfactory Y/N/NA
(7.17.3) Step 2: Add POTS Card(s) Interface VLANs to Static VLAN satisfactory Y/N/NA
(7.17.4) Step 3: Configure UK National Mapping satisfactory Y/N/NA
(7.17.5) Step 4: Configure ITAM for Double Play satisfactory Y/N/NA
(7.17.6) Step 5: Configure RTP Profiles satisfactory Y/N/NA
(7.17.7) Step 6: Check TOIP Profiles satisfactory Y/N/NA
(7.17.8) Step 7: Configure POTS card(s) satisfactory Y/N/NA
(7.17.9) Step 8: Build Voice Configuration satisfactory Y/N/NA
(8.1.1) Optical Launch Power measurements satisfactory Y/N/NA
CP SFP Module Port 1 measurement -dBm
CP SFP Module Port 1 measurement -dBm
(8.1.2) Unit Status Check satisfactory Y/N/NA
(8.2.1) Common Part Alarm Check satisfactory Y/N/NA
(8.2.2) Power Supply Alarm Check satisfactory Y/N/NA
(8.2.3) Fan Unit Alarm Check satisfactory Y/N/NA
(8.2.4) 64 x ADSL2+ Unit Alarm Check satisfactory Y/N/NA
(8.2.5) 32 x SHDSL Unit Alarm Check satisfactory Y/N/NA
(8.2.6) 64 x POTS/VoIP Unit Alarm Check satisfactory Y/N/NA
(8.3) Set Equipment date and Time satisfactory Y/N/NA
(9.1) Configure/Activate/Test 64 x ADSL2+ Units satisfactory Y/N/NA
(9.2) Configure/Activate/Test 32 x SHDSL Units satisfactory Y/N/NA
(9.3) Test 64 x POTS/VoIP Units satisfactory Y/N/NA
(9.4) iTAM Splitter Connection Units:- Y/N/NA
(9.4.1) Check Test Relay Switching satisfactory Y/N/NA
(9.4.2) Configure iTAM Splitter Units satisfactory Y/N/NA
(9.4.3) Continuity Testing LLUT(Line) to LLUL(POTS) Blocks satisfactory Y/N/NA
(9.5) End of Standalone Configuration/Testing satisfactory Y/N/NA
To Next Page
Loading...