Ericsson EDA 2530 - Page 4

EDA 2530 Commissioning Procedure for Cable and Wireless Access
1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01
© Ericsson AB 2010
Commercial in confidence
4 (200)
4.5.1 Labelling.................................................................................................45
5 Initial Configuration .............................................................................47
5.1 IP Address Configuration Of PC Used As LCT ......................................47
5.2 Common Part Card CF Download..........................................................50
5.3 Subrack Equipping .................................................................................53
5.4 Logon to The EDA 2530 Via LCT...........................................................54
5.5 Reset The Backplane EPROM...............................................................55
5.6 Software Inventory Check ......................................................................57
6 Software Download/Upgrade ..............................................................61
7 Configure IP and Ethernet Management............................................67
7.1 Configure The Optical SFP Modules Gigabit Ethernet...........................69
7.2 Configure CP Ethernet Interfaces ..........................................................72
7.2.1 Configure CP Port 1 ...............................................................................72
7.2.2 Configure CP Port 2 ...............................................................................73
7.2.3 Configure CP Port 3 (If required)............................................................73
7.2.4 Configure CP Port 4 (If required)............................................................73
7.3 Configure EDA 2530 Tag Protocol ID/Bridging Parameters...................74
7.4 ADSL Card Configuration Files ..............................................................75
7.5 SHDSL Card Configuration Files............................................................75
7.6 Configure Static VLANs..........................................................................76
7.7 Adding Interfaces to the Static VLANs ...................................................79
7.7.1 Create S-VLANs for Additional ADSL Cards (If required) ......................81
7.7.2 Create S-VLANs for SHDSL Cards (If required) ....................................83
7.7.3 Create S-VLANs for POTS Cards (If required).......................................85
7.7.4 Complete VLAN Creation.......................................................................88
7.7.5 Create S-VLANs on the “Parent” to Subtend Child#2 (If required).........88
7.7.6 Create S-VLANs on the “Parent” to Subtend Child#3 (If required).........94
7.8 Configuring The IBM Sub-Interface........................................................96
7.9 Assign The IBM IP Address ...................................................................98
7.10 Configure The Default Gateway...........................................................100
7.11 xDSL Bridge Management - Configure xDSL Bridge ...........................101
7.12 xDSL Bridge Management - Configure PVC ........................................104
7.12.1 Download xDSL PVC Management File ..............................................104
7.12.2 Check PVC Management PPPoA Payload & MRU Settings................105
7.12.3 Configure PVC Management ...............................................................106
7.12.4 Configure Additional xDSL Cards.........................................................111
7.13 xDSL Bridge Management – Downstream Flow Assignment...............112
7.14 Configure ADSL Profiles ......................................................................114
7.15 Configure SHDSL Line Profiles............................................................116
7.16 Configure SHDSL Stack Profiles..........................................................118
7.17 Configure POTS Card(s) ......................................................................121
7.17.1 POTS Card Configuration Files............................................................121
7.17.2 Step 1: LCT 07.02.05 – Known Issue with Java Version 1.6 ...............121
7.17.3 Step 2: Add POTS Card(s) Interfaces to Static VLANs........................121
7.17.4 Step 3: Configure UK National Mapping ..............................................122
7.17.5 Step 4: Configure ITAM For Double Play .............................................124
7.17.6 Step 5: Configure RTP Profiles ............................................................126
7.17.7 Step 6: Check TOIP Profiles ................................................................130
7.17.8 Step 7: Configure POTS Cards ............................................................131