FAAC B680H - Page 36

8
ENGLISH
Dip 1 Dip 2 Dip 3 Dip 4 Pair
no.
Type
ON OFF OFF OFF
1°Pair
CLOSE
photocells
ON OFF OFF ON
2°Pair
ON OFF ON OFF 3°Pair
ON OFF ON ON 4°Pair
ON ON OFF OFF 5°Pair
ON ON OFF ON 6°Pair
ON ON ON OFF 7°Pair
ON ON ON ON Single OPEN
PULSE
DIP-SWITCH
TX
DIP-SWITCH
RX
SAME
ADDRESS
4.1.2 Connecting BUS photocells
Up to 8 pairs of photocells can be connected to the E680 control board
using BUS technology.The connection must be made in parallel,
onterminalboardJ6,usingasinglepower/communicationline,as
showninFig.27.
BUS photocells do not require a matching polarity
connection.
The8pairsofphotocellsfeaturethefollowingfunctions:
Pairsofclosingphotocells:   max7
PairsofOPENpulsephotocells:  max1
After positioning the BUS technology photocells, it is necessary
toproceed with selecting the address foreach pair using various
combinations of the DIP-SWITCHES located on each photocell.
Set the SAME DIP-SWITCH ADDRESS chosen both on
the transmitter and receiver of the same pair.
Ensure that two or more pairs of photocells do not have
the same address. If no BUS accessories are used, leave
terminals 1 and 2 free.
Thefollowing table describeshow to set thedip-switches located
inside the transmitter and receiver of the BUS photocells.
Addressing BUS photocell PAIRS
To allow operation of the installed BUS accessories,
store them on the board as described in paragraph 5.3.
4.2 Terminal board J2 (outputs)
OUT 1 - Output 1 open-collector GND (terminal 13):Theoutputcan
besetinoneofthefunctionsdescribedintheAdvancedConfiguration
(par. 6).The default value is 04 - Beam OPEN or in PAUSE.
Maximum load: 24 VDC with 100 mA.
OUT 2 - Output 2 open-collector GND (terminal 15):
Theoutputcan
besetinoneofthefunctionsdescribedintheAdvancedConfiguration
(par.6).Thedefaultvalueis03 - CLOSED BEAM. Maximum load:
24 VDC with 100 mA.
OUT 3 - Output 3 open-collector GND (terminal 17):
Theoutputcan
besetinoneofthefunctionsdescribedintheAdvancedConfiguration
(par.6).Thedefaultvalueis19 -WARNINGLAMP.Maximum load:
24 VDC with 100 mA.
OUT 4 - Relay output 4 (terminals 19, 20, 21): Theoutputcanbe
setinoneofthefunctionsdescribedinAdvancedConfiguration(par.
6).Thedefaultvalue is01 - BEAM ILLUMINATION. Maximum
load: 24 VDC with 800 mA.
4.3 Terminal board J3 (external ashing lamp)
LAMP:tothese terminals you can connect a 24VDC FAACLED
externalflashinglamp.The integrated flashing traffic light must be
connected independently to connector J15.
The 24V FAACLIGHT with incandescent lamp cannot be
connected to the J3 connector
4.4 Terminal board J4 (loop detector)
LOOP 1: magneticloop LOOP1(OPEN,terminals 24-25): for
OPENING.
LOOP 2:
magneticloopLOOP2(SAFETY/CLOSE,terminals26-27):
for SAFETY/CLOSING.
4.5 Connector J5 (Motor)
Rapidconnectorforconnectingthemotor.
4.6 Connector J7 (Encoder)
TheB680Hbarrierisequippedwithadevicefordetectingtheopening
angle/barpositiontoensuregreateranti-crushingsafetythanksto
thepossibilityofreversingthedirectionofmovementthemomentin
which an obstacle is detected. This device interfaces with the board
throughconnectorJ7.
4.7 Connector J10 (Radio)
UsedfortherapidconnectionoftheMinidec,DecoderandRP/RP2
Receivers(seeFig.28).Ifa2-channelreceiverisused,liketheRP2,
itwillbepossibletodirectlycommandautomatedsystemOPENand
CLOSEfroma2-channelradiocontrol.Ifa1-channelreceiverisused,
liketheRP,itwillonlybepossibletocommandOPEN.
Connecttheaccessory withthecomponents sidefacingthe main
strip of the board.
Boards should be inserted and removed ONLY after
having cut off electrical power
4.8 Connector J11 (Beam break-out sensor)
Designedforconnectingthebreak-outsensorforthepivotingbeam
(ifpresent).Thesensorisoptional.Ifitisnotpresent,do not remove
theinstalledjumper.
4.9 Connector J12 (Emergency battery)
Thisconnectoris for connecting a battery (optional) for ensuring
automatedsystemoperationincaseoftemporarycutoffofthemain
powersupply.
4.10 Connector J13 (36VDC Power Supply)
Thisfactory-wiredconnectorpowerstheE680board
4.11 Connector J15 (ashing trafc light)
Thisconnectorisforconnectingthe flashing traffic light built into
the barrier head.The flashing traffic light visually signals barrier
movementand,ifneeded,regulateaccess to the property using
trafficlightsignals.
5. PROGRAMMING
TheE680boardfeatures3programminglevelsthatmakeitentirely
configurableandallowittoadaptthelogicstoanyuse.
Each of the three levels can be accessed through a specific key
combination.