Fike ECS Series User Manual (English)

To Next Page

P/N LS10145-002FK-E:A • ECN 151526

Document LS10145-002FK-E

3/12/2021

Addressable Fire Alarm Control Panel

FCP-300/FCP-300ECS

Installation/Operation Manual

Table of Contents5
Section 1: Introduction10
System Overview10
1: Hardware Features10
2: Network System Hardware Features10
3: Software Features10
4: FCP-300ECS Features10
5: Terms Used in this Manual11
Compatible Products11
Section 2: Agency Listings, Approvals, and Requirements13
Federal Communications Commission (FCC)13
Underwriters Laboratories (UL)14
1: Requirements for All Installations14
2: Central Station Fire Alarm Systems Requirements14
3: Local Protected Fire Alarm Systems Requirements14
4: Remote Station Protected Fire Alarm Systems Requirements14
5: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72014
6: NFPA Requirements14
Section 3: Installation Requirements16
Inventory16
Environmental Specifications16
Software Downloads16
Electrical Specifications16
Wiring Specifications17
Board Assembly Diagram19
Calculating Current Draw and Standby Battery19
1: Current Draw Worksheet Requirements19
2: Current Draw Worksheet for FIK SLC Devices20
3: Maximum Battery Standby Load23
Section 4: Control Panel Installation24
Mounting the Control Panel Cabinet24
1: Preventing Water Damage24
2: Removing the FCP-300/ECS Assembly from the Housing24
3: Ethernet Connection24
AC Connection25
Battery Power25
1: RBB Accessory Cabinet26
SBUS Wiring27
1: Calculating Wiring Distance for SBUS Modules27
2: Wiring Configurations29
FIK-RA100 Remote Annunciator Installation30
1: Mounting the FIK-RA10030
2: Connecting the FIK-RA100 to the Panel33
FIK-RA1000 Remote Annunciator Installation33
1: Mounting the FIK-RA100034
2: Connecting the FIK-RA1000 to the Panel35
FIK-RA2000 Remote Annunciator Installation35
1: Mounting the FIK-RA200036
2: FIK-RA2000 Connection to the Panel38
FIK-6815 Installation38
1: FIK-6815 Connection to the Panel39
FIK-5824 Serial/Parallel Interface Module Installation39
1: Selecting FIK-5824 Options40
FIK-5880 LED I/O Module41
1: FIK-5880 Board Layout41
2: FIK-5880 Connection to Panel42
3: LED Wiring42
4: Dry Contact Wiring43
FIK-5865-3/FIK-5865-4 LED Annunciator Installation43
1: FIK-5865 Connection to Panel44
2: FIK-5865 Mounting44
Configuring SBUS Modules45
1: Assigning SBUS Module Ids45
2: SBUS Bandwidth Considerations46
Telephone Connection46
Notification Appliance/Auxiliary Power Circuits46
1: Conventional Notification Appliance46
2: Auxiliary Power Installation48
On-Board Relays (Conventional)49
1: Trouble Relay49
2: Programmable Relays49
Remote Station Applications49
1: Keltron Model 3158 Installation49
2: City Box Connection Using the 5220 Module50
Using the Addressable Relay Module for City Box Connection51
1: NFPA 72 Polarity Reversal52
2: Transmitter Activated by Dry Contacts54
Section 5: Networking55
Network System Hardware Features55
1: Networked Sites55
2: Wiring Options/Requirements to Connect Networked Panels55
Network Wiring55
FIK-NIC Wiring Options56
1: Fiber Loop Modules56
2: FIK-NIC Installation58
Setting the Network ID for each Panel60
Section 6: Network Management61
Network Diagnostics61
1: Ping Panel61
2: Data Network Status61
3: Voice Network Status61
Network Programming61
1: Learn Network61
2: Edit Network Names61
3: Edit Panel ID61
4: Computer Access62
5: Access Codes62
6: Communicator Options63
Voice Options65
1: Edit Timers65
2: Edit Voice Commands65
Sync Network Options66
Network Management Quick Reference67
Section 7: Fike and SWIFT SLC Device Installation69
List of Fike SLC Devices69
SWIFT Wireless SLC Devices69
Maximum Number of SLC Devices69
Wiring Requirements for SLC Devices69
1: Wire Sizing for FIK-681570
2: Wiring Requirements for Fike Modules70
3: Wiring FIK-6815 in Style 6 & 7 (Class A) Configuration71
Addressing the Fike SLC Devices72
Addressing SD Devices72
1: SLC Devices with DIP Switches73
WIDP-WGI Wireless Gateway73
1: Power Connections for the Gateway73
Section 8: Programming Overview74
Jumpstart® Auto-Programming74
1: Input Points74
2: Output Points74
3: Running Jumpstart Auto-Programming74
Mapping Overview75
1: Input Point Mapping75
2: Output Circuit Mapping77
3: Event Mapping77
4: Mapping LED Points81
5: Mapping LED Points for a Networked System82
Programming Using the HFSS Software Suite82
Programming Using an Annunciator82
1: Entering / Exiting the Panel Programming82
2: Moving through the Menus83
3: Selecting Options and Entering Data83
Programming Menu Quick Reference83
Section 9: Programming92
UL 864 / UL 2572 Programming Requirements92
Modules92
1: Edit Modules92
2: Adding a Module93
3: Deleting a Module93
4: View Module List93
Zone93
1: Edit Zone94
2: View Zone Points96
Group96
1: Edit Group96
2: View Group Points97
3: Edit OPG Template97
Point98
1: Point Programming for FIK-6815 Module98
2: Point Programming for the Internal or the External Power Module (FIK-RPS1000)100
3: Point Programming for FIK-5880 or 5865 Modules101
4: Point Programming for FIK-5496102
5: Point Programming for FIK-AMP102
6: Point Programming for FIK-NVCM and FIK-RVM Modules103
System Options105
1: Communication Options105
2: Daytime/Nighttime Sensitivity108
3: Holiday Days108
4: Time Options109
5: Miscellaneous Options109
6: Daylight Saving Options110
7: Edit Banner110
8: SLC Family110
Jumpstart® Autoprogramming111
Restore Defaults111
Voice Options111
1: FIK-NVCM Maintenance111
2: Voice Settings111
Section 10: System Operation112
Default User and Installer Codes112
Annunciator Description112
1: LCD Display112
2: Banner112
3: Single Key Acknowledge113
Menu System113
1: Main Menu Overview113
2: Using the Menus113
Basic Operation113
1: Setting Time and Date113
2: Disable / Enable a Point113
3: View Event History114
4: Conduct a Fire Drill114
5: Conduct an Indicator Test114
6: Conduct a Walk Test115
7: Conduct a Communicator Test115
8: Manual Alarmnet Registration115
9: Silence Alarms or Troubles115
10: Reset Alarms115
11: Check Detector Sensitivity through Point Status116
12: View Status of a Point116
13: View Alarms or Troubles116
14: System Information116
Event Priority117
1: System Control117
2: System Override117
4: Priority Rules118
5: Other Priority Considerations118
Operation Mode Behavior118
1: Multi-Site Annunciator and Multi-Site User Access121
Releasing Operations121
1: Single Interlock Zone Releasing122
2: Double Interlock Zone Releasing123
Smoke Alarm Verification124
Function Keys124
1: Recording an F-Key Macro124
2: Aborting an F-Key Macro Recording Session124
3: Erasing an F-Key Macro124
4: Using a Recorded F-Key Macro124
5: F-Key Status Event124
6: F-Key Map Inhibit124
Section 11: Emergency Communication System Operation125
Overview125
LOC Functionality125
1: Keys and Leds125
2: Gaining ECS Control126
3: Manual ECS126
4: Microphone Mode127
5: Message Mode127
6: Custom ECS Event127
7: Passing ECS Control127
8: Exit ECS Control Menu128
9: Relinquish ECS Control128
10: ECS Reset128
ECS Super User128
ECS Point Functionality128
1: ECS Point Activations128
2: FIK-NVCM & FIK-RVM Points129
Amplifier Programming129
1: Adding an Amplifier129
2: Editing an Amplifier129
LOC Programming129
1: Adding an LOC129
2: Editing an LOC130
Using the Microphone130
1: Microphone Functionality130
2: Custom ECS Event130
3: Fire Page130
Recording Custom Messages131
1: Recording Messages 1-15 Using Aux Audio Input132
2: Recording Messages 1-15 Using the Microphone133
3: Erasing User Message134
4: Using HFSS Voice Message Load Software134
Network Paging135
Section 12: Reporting136
Receivers Compatible with the Control Panel136
SIA - FCP-300/ECS Panels PI Modifier Contact Reporting143
SIA - Panel Communicator144
Section 13: Testing and Troubleshooting145
Troubleshooting145
Event History146
Built-In Troubleshooting and Testing Tools146
1: SLC Device Locator146
2: SLC Multiple Device Locator146
3: I/O Point Control147
4: Earth Fault Resistance147
Section 14: Installation Records148
Detector and Module Point Record148
Conventional Output Point Record150
Appendix A: Compatible Devices151
A.1: Notification Appliances151
A.1.1: Two Wire Detectors158
A.2: Four-Wire Smoke Detectors/Devices (UL Listed)159
A.3: Door Holders (UL Listed)161
A.4: Relays (UL Listed)161
A.5: Compatible 520Hz Signaling Speakers162
A.6: Compatible 520Hz Low Frequency Bases162
Appendix B: Editing Text Using the Built-In Programmer163
B.1: Characters Used for Editing Text163
B.2: Example Name Edit163
Appendix C: Expanded Receiver/Panel Relationship164
Appendix D: Cadence Patterns165
Appendix E: Panel Security166

Other manuals for Fike ECS Series

Manual160 pages

Need help?

Do you have a question about the Fike ECS Series and is the answer not in the manual?

Fike ECS Series Specifications

General

Brand	Fike
Model	ECS Series
Category	Fire Alarms
Language	English

Related product manuals

Fike ECS Series User Manual

Table of Contents

Other manuals for Fike ECS Series

Fike ECS Series Specifications

Related product manuals