To Next PageTo Next PageWhy does my Froling P2-25 Boiler show a 'Stoker error'?
A 'Stoker error' on your Froling Boiler means the gravity shaft level sensor still detects material after 10 minutes of stoker operation. This may be caused by a fuel bridge in the gravity shaft, an incorrectly set sensor, or the stoker not feeding. Break up any fuel bridges, readjust the sensor, and check the stoker drive.
What to do if Froling Boiler says 'Door open - Empty ash box'?
If the Froling Boiler displays 'Door open - Empty ash box', it means the insulating doors have been open for over 10 minutes during heating, the door contact switch isn't closing, or the ash box is full. To resolve this, check or adjust the switch, ensure the insulating doors are closed properly, and empty the ash box.
How to fix a Froling P2-25 with nothing on the display?
If nothing is showing on the Froling Boiler's display, it could be due to a general power failure, a tripped FI circuit breaker, the main switch being off, or a defective fuse. To fix this, switch on the FI circuit breaker, turn on the main switch, or replace the fuse (10AT).
What to do if my Froling Boiler says 'Check storage room'?
If your Froling Boiler displays 'Check storage room', it indicates that the MAX sensor wasn't reached after 10 minutes of suction. This could be due to no pellets in the suction probe, a blockage in the hose, or a faulty sensor. Refill pellets, remove any blockages, and readjust the sensor. Also, check the plug connection to the motor.
What to do when Froling Boiler says 'Clean /check burner'?
The 'Clean/check burner' message on your Froling Boiler signals successful automatic troubleshooting. Acknowledge the warning, then open the insulating and combustion chamber doors. Clean embers, fuel, and slag from the pellet burner. Clean the flue gas guide in the boiler up to the chimney mouth, and empty the ash drawer.
Introduction to the P2 Pellet Boiler and its Lambdatronic P 3100 control system.
Covers general safety, permitted uses, fuel, design information, and installation standards.
Details safety devices, installation room safety, other risks, and emergency response protocols.
How to change parameters and an overview of inspection and cleaning procedures.
A comprehensive reference for all configurable parameters within the control system.
Essential warnings regarding boiler use, external influences, and flue gas system safety.
Identifies critical safety components like the STOP key, main switch, and fuses.
Explains devices preventing overheating and safety precautions for the installation room environment.
Warns about hot parts, safe work practices, and the dangers of using unauthorized fuel.
Procedures for system overheating, responding to flue gas, and fire safety protocols.
Detailed descriptions of various operating modes like Winter, Summer, Transitional, and Cleaning.
Explanations for different operating statuses, including preparation, heating, and fault conditions.
Critical safety warnings and procedures to follow before performing any maintenance tasks.
Procedures for inspecting the combustion chamber, checking ash levels, and examining the pellet burner.
Step-by-step instructions for safely removing ash from the boiler's ash drawer or ashcan.
Steps to diagnose and fix issues related to power supply and excessive boiler temperatures.
Guide on how to interpret fault messages and the procedure for clearing them.
Lists error codes, their causes, and corrective actions for sensor, stoker, and remote control faults.
Lists error codes, their causes, and corrective actions for system, boiler, and solar related faults.
Lists error codes, their causes, and corrective actions for outfeed and suction system errors.
Lists error codes, their causes, and corrective actions for key switch, safety limiter, and return temperature issues.
Lists error codes, their causes, and corrective actions for safety time, pellet feed, and ignition faults.
Lists error codes, their causes, and corrective actions for air settings, flow temperature, and boiler errors.
Lists error codes, their causes, and corrective actions for ignition and stoker feed faults.
Configuration options for boiler temperature, storage tank levels, and DHW tank temperatures.
General