Fulton ProtoNode Start-up Guide
Page 4 of 47
TABLE OF CONTENTS
1 Certification .......................................................................................................................................... 7
1.1 BTL Mark – BACnet
®
Testing Laboratory ....................................................................................... 7
2 Introduction .......................................................................................................................................... 8
2.1 ProtoNode Gateway ....................................................................................................................... 8
3 ProtoNode Setup.................................................................................................................................. 9
3.1 Record Identification Data .............................................................................................................. 9
3.2 Point Count Capacity and Registers per Device ............................................................................ 9
3.3 Configuring Modbus Device Communications ............................................................................. 10
3.3.1 Confirm the Device and ProtoNode COM Settings Match ...................................................... 10
3.3.2 Set Node-ID for Any Device Attached to the ProtoNode ........................................................ 10
4 Interfacing ProtoNode to Devices .................................................................................................... 11
4.1 Device Connections to ProtoNode ............................................................................................... 11
4.1.1 Interfacing ProtoNode to ModSync SE ................................................................................... 11
4.1.2 Interfacing ProtoNode to Honeywell SOLA Controller ............................................................ 12
4.1.3 Interfacing ProtoNode to Endura+ (PURE) Controller ............................................................ 13
4.1.4 Interfacing ProtoNode to Siemens LMV3x Controller ............................................................. 14
4.1.5 Interfacing ProtoNode to Siemens LMV5x Control ................................................................. 15
4.1.6 Interfacing ProtoNode to Siemens LMV3x and Yokogawa Controllers .................................. 16
4.1.7 Interfacing ProtoNode to Siemens LMV3x and RWF55 Controllers ....................................... 17
4.2 Wiring Field Port to RS-485 Serial Network ................................................................................. 18
4.3 Bias Resistors ............................................................................................................................... 19
4.4 Termination Resistor..................................................................................................................... 20
4.5 Power-Up ProtoNode.................................................................................................................... 22
5 Connect the PC to the ProtoNode .................................................................................................... 23
5.1 Connecting to the ProtoNode via Ethernet ................................................................................... 23
5.1.1 Changing the Subnet of the Connected PC ............................................................................ 23
6 Configure the ProtoNode .................................................................................................................. 24
6.1 Accessing the ProtoNode Web Configurator ................................................................................ 24
6.2 Select Field Protocol and Set Configuration Parameters ............................................................. 26
6.3 Set ProtoNode Active Profiles ...................................................................................................... 27
6.4 Verify Device Communications ..................................................................................................... 28
6.5 Ethernet Network: Setting IP Address for the Field Network ....................................................... 29
6.6 How to Start the Installation Over: Clearing Profiles .................................................................... 31
7 SMC Cloud User Setup, Registration and Login ............................................................................ 32
Appendix A Troubleshooting ................................................................................................................... 33
Appendix A.1 Lost or Incorrect IP Address ............................................................................................. 33
Appendix A.2 Viewing Diagnostic Information ........................................................................................ 34
Appendix A.3 Checking Wiring and Settings ........................................................................................... 35
Appendix A.4 LED Diagnostics for Communications Between ProtoNode and Devices ........................ 36
Appendix A.5 Take a FieldServer Diagnostic Capture ............................................................................ 37
Appendix A.5.1 Using the FieldServer Toolbox ................................................................................... 37
Appendix A.5.2 Using FS-GUI ............................................................................................................. 40
Appendix B Additional Information ......................................................................................................... 41
Appendix B.1 Updating Firmware ............................................................................................................ 41
Appendix B.2 Securing ProtoNode with Passwords ............................................................................... 42
Appendix B.3 Factory Reset Instructions ................................................................................................ 43
Appendix B.4 Internet Browsers Not Supported ..................................................................................... 43
Appendix B.5 Mounting ........................................................................................................................... 43
Appendix B.6 Physical Dimension Drawing ............................................................................................ 44
Appendix C Vendor Information – Fulton ............................................................................................... 45
Appendix D Reference .............................................................................................................................. 46
Appendix D.1 Specifications .................................................................................................................... 46
Appendix D.1.1 Compliance with UL Regulations ............................................................................... 46
To Next Page
Loading...