59
5. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display
shows the new setting for the selected schedule.
6. Repeat steps 3, 4, and 5 until all desired outputs are attached to schedules.
Arming (Attach Schedules To Events)
(0660nn where nn = Schedule number [0 to 15])
Note
This setting will allow you to
arm to AWAY only. There is
no disarm schedule.
(Default = off) This setting lets you arm according to a time schedule.
¾
To Attach Schedules to Arming:
1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS.
2. Press # then A or B until the display shows
ARMING.
3. To select arm to AWAY press #.
4. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different
schedule, press A or B until the desired schedule appears.
5. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display
shows the new setting for the selected schedule.
6. Repeat steps 4 and 5 until all desired schedules are attached.
Energy Saver Menu
The ENERGY SAVER menu lets you set the energy saver module low- and high-setpoints. These
setpoints determine when the module relay closes, thereby completing the circuit through the
thermostat to the furnace/air-conditioner.
Low Setpoint (Energy Saver)
(070)
(Default = 50°F) This setting determines the temperature at which the energy saver module relay
closes to activate the furnace.
Note
The low setpoint cannot be
set equal to or higher than
the high setpoint.
¾To set the Low Setpoint:
1. With the display showing ENERGY SAVER, press #, then A or B until the display shows LOW
SETPOINT NN DEGREES
(current setting).
2.
Enter the desired temperature (45–89°). The display flashes the entered setting. Press # and the
display shows the new setting.
High Setpoint (Energy Saver)
(071)
(Default = 90°F) This setting determines the temperature at which the energy saver module relay
closes to activate the air-conditioner.
Note
The high setpoint cannot be
set equal to or lower than
the low setpoint.
¾To set the High Setpoint:
1. With the display showing ENERGY SAVER, press #, then A or B until the display shows HIGH
SETPOINT nn DEGREES (current setting).
2.
Enter the desired temperature (46–90°). The display flashes the entered setting. Press # and the
display shows the new setting.
Attach Lights to Sensors Menu
The ATTACH LIGHTS TO SENSORS menu lets you assign a light number to a sensor. Each time the
sensor is activated, the attached light will turn on for 5 minutes. When the 5 minute timer expires
the light will turn off. If the same light is scheduled, it will only turn on during the schedule time
Light x to Sensor Y (Attach Lights to Sensors)
(08n where n = light number [1–9] minus 1)
(Default = 0) This menu attaches light x to sensor y. Each time a selected sensor is tripped, the
selected light will turn on and a 5 minute timer will start.
Note
The sensor must be learned
into the current partition
before it can be attached.
¾To attach a light to a sensor:
1. With the display showing LIGHT 1 TO SENSOR y (current setting), press A or B to select the
desired light number.
2. Enter the desired sensor number (01–76). The display flashes the entered setting. Press # and
the display shows the new setting.
3. Repeat steps 1 through 2 until all desired lights are attached to sensors.
¾
To detach a light from a sensor:
1. With the display showing LIGHT 1 TO SENSOR y (current setting), press A or B to select the
desired light number.
2. Enter 0 as the sensor number and press #.
To Next Page
Loading...
