GE Interlogix Concord Security System User Manual

Concord 60
Direct Bypassing
(030nnn1 where nnn=user
number 00-229)
User Codes-Reg. User Codes-User NNN (Default = off)
This setting determines whether
or not a specific user code pro-
vides access to the “bypass sen-
sors” feature. Set this feature to
“on” for all users who need to be
able to bypass sensors.
¾
To turn user code Direct Bypassing off or on:
1. With the display showing USER CODES, press # and the display shows REGULAR USER
CODES.
2. Press #
and the display shows USER nnn (first available user number).
3. Press A or B to select the desired user number, then press #. The display shows
USER
nnn - nnnn.
4. Press A or B until the display shows DIRECT BYPASSING OFF/ON (current setting).
5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display
shows the new setting.
Remote Access
(030nnn2 where nnn=user
number 00-229)
User Codes-Reg. User Codes-User NNN (Default = off)
This setting determines whether
or not the user can access the
panel from a remote phone (a
phone located off the premises).
¾
To turn user code Remote Access off or on:
1. With the display showing USER CODES, press # and the display shows REGULAR USER
CODES.
2. Press #
and the display shows USER nn (first available user number).
3. Press A or B to select the desired user number, then press #. The display shows
USER
nnn - nnnn.
4. Press B until the display shows REMOTE ACCESS ON/OFF (current setting).
5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display
shows the new setting.
Partition Jump
(030nnn3 where nnn=user
number 00-229)
User Codes-Reg. User Codes-User NNN (Default = off)
This setting determines whether
or not a specific user code can
access one or both partitions.
When this is set to on, the user can
access both partitions.
Note
This option is not available if using a
partition master code.
¾To turn user code Partition Jump off or on:
1. With the display showing USER CODES, press # and the display shows REGULAR USER
CODES.
2. Press #
and the display shows USER nnn (first available user number).
3. Press A or B to select the desired user number, then press #. The display shows
USER
nnn - nnnn.
4. Press B until the display shows
PARTITION JUMP OFF/ON (current setting).
5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display
shows the new setting.
System Tests
(030nnn4 where nnn=user
number 00-229)
User Codes-Reg. User Codes-User NNN (Default = off)
This setting determines whether
or not a specific user code pro-
vides access to the phone and sen-
sor tests. Set this feature to “on”
for all users who need to be able
to conduct phone and sensor tests.
¾
To turn user code System Tests off or on:
1. With the display showing USER CODES, press # and the display shows REGULAR USER
CODES.
2. Press #
and the display shows USER nnn (first available user number).
3. Press A or B to select the desired user number, then press #. The display shows
USER
nnn - nnnn.
4. Press A or B until the display shows
SYSTEM TESTS OFF/ON (current setting).
5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display
shows the new setting.

GE Interlogix Concord Security System Specifications

General

Brand	GE Interlogix
Model	Concord Security System
Category	Security System
Language	English