GE Interlogix Concord Security System User Manual

Concord
61
Options Menu
The OPTIONS menu lets you set up the system for downloading and silent arming. You can also
adjust alphanumeric touchpad display brightness from this menu.
Latchkey Report
(030nnn5 where nnn=user
number 00-229)
User Codes-Reg. User Codes-User NNN (Defaults: 00-05 = on, 06-229 = off)
This setting determines whether
or not the user code causes a
latchkey report to be sent to a
pager when the code is used to
change arming levels.
¾
To assign the Latchkey Report attribute to user codes:
1. With the display showing USER CODES, press # and the display shows REGULAR USER
CODES.
2. Press #
and the display shows USER nnn (first available user number).
3. Press A or B to select the desired user number, then press #. The display shows
USER
nnn - nnnn
.
4. Press A or B until the display shows
LATCHKEY OFF/ON (current setting).
5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display
shows the new setting.
Partition Master
(partition 1: 0310, partition 2: 0311)
User Codes-Partition Master Code (Default = none)
The Partition Master Code provides access to all system
operations and user programming for a single partition.
Note
You must be “in” the partition of the partition master code
you wish to change.
¾To change the Partition Master Code:
1. With the display showing USER CODES, press # then A or B
until the display shows
PARTITION MASTER CODE.
2. Press #
and the display shows PARTITION nnnn (current code).
3. Enter a new 4-digit code. The display flashes the entered code.
Press # and the display shows the new code.
System Master (0320)
User Codes-System Master Code (Default = 1234)
The System Master Code provides
access to all system operations and user
programming.
¾
To change the System Master Code:
1. With the display showing USER CODES, press # then A or B until the display
shows
SYSTEM MASTER CODE.
2. Press #
and the display shows SYSTEM MASTER nnnn (current code).
3. Enter a new 4-digit code. The display flashes the entered code. Press # and dis-
play shows the new code.
Downloading (040)
Options (Default = on)
When this setting is on, the panel can communicate with Tool-
Box
®
software for programming the system from off-site.
Note
For this feature to work, the panel must be connected to a phone line
and be programmed with REMOTE ACCESS on, with a Downloader
phone number, and with a Downloader code.
¾To turn Downloading off or on:
1. Press A or B until the display shows OPTIONS.
2. Press #, then A or B until the display shows
DOWN-
LOADING OFF/ON
(current setting).
3. Press 1 (off) or 2 (on). The display flashes the entered
selection. Press
# and the display shows the new setting.
Silent Arming (041)
Options (Default = off)
This setting determines whether or not the panel sounds status
beeps from sirens and the touchpad when the system is armed.
Note
When this feature is on, the user does not need to press 5 (SILENT)
before arming the system to prevent status sounds. When SIA False
Alarm Reduction (0004) is ON, this option is disabled.
¾To turn Silent Arming off or on:
1. Press A or B until the display shows OPTIONS.
2. Press #, then A or B until the display shows
SILENT
ARMING OFF/ON
(current setting).
3. Press 1 (off) or 2 (on). The display flashes the entered
selection. Press
# and the display shows the new setting.

GE Interlogix Concord Security System Specifications

General

Brand	GE Interlogix
Model	Concord Security System
Category	Security System
Language	English