GE D30

x D30 LINE DISTANCE PROTECTION SYSTEM – INSTRUCTION MANUAL
INDEX
P
Panel cutout .....................................................................................3-2, 3-6
Parallel Redundancy Protocol
actual values ...................................................................................... 6-11
explained ............................................................................................. 5-46
settings ................................................................................................. 5-44
specifications ..................................................................................... 2-33
Parity .......................................................................................................... 5-41
Part numbering ....................................................................................... 2-7
Passwords
authentication by device or server .......................................... 5-15
bypass authentication ................................................................... 5-22
change .................................................................................................. 4-59
change after installation .............................................................. 3-69
change does not take relay out of service ............................. 5-1
command .......................................................................4-59, 5-9, 5-10
default ................................................................................................... 5-13
explained ................................................................................................2-4
FlexLogic operands .......................................................................5-175
lockout ...................................................................................... 4-60, 5-13
lost password ....................................................................................... 5-7
requirements ........................................................................................5-8
reset to factory defaults .................................................................. 5-7
rules ...........................................................................................................5-8
settings ............................................................................4-59, 5-9, 5-10
settings templates ..............................................................................4-7
wrong entry ........................................................................................ 4-60
Permissive functions .......................................................................5-253
Per-unit quantity ....................................................................................5-4
Phase angle metering ...................................................................... 6-13
Phase current metering .................................................................. 6-16
Phase directional overcurrent
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-231
phase A polarization .....................................................................5-229
settings ...............................................................................................5-228
specifications ..................................................................................... 2-21
Phase distance
FlexLogic operands .......................................................................5-170
OP scheme ........................................................................................5-201
settings ...............................................................................................5-193
specifications ..................................................................................... 2-18
Phase IOC
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-228
settings ...............................................................................................5-227
specifications ..................................................................................... 2-21
Phase overvoltage
FlexLogic operands .......................................................................5-171
logic diagram ...................................................................................5-255
settings ...............................................................................................5-255
specifications ..................................................................................... 2-23
Phase rotation ....................................................................................5-143
Phase TOC
FlexLogic operands ...................................................................... 5-171
logic diagram .................................................................................. 5-227
settings ............................................................................................... 5-225
specifications .....................................................................................2-20
Phase undervoltage
FlexLogic operands ...................................................................... 5-171
logic diagram .................................................................................. 5-254
settings ............................................................................................... 5-254
specifications .....................................................................................2-22
Phasor display graphical front panel .......................... 4-57, 5-31
Phasor estimation ..................................................................................9-2
Pickup, line ........................................................................................... 5-189
Plastic film on front panel ........................................................... 10-20
Port
Ethernet, turn on or off ..................................................................5-44
failure monitoring ............................................................................5-37
HTTP, close ..........................................................................................5-99
IEC 60870-5-104, close ............................................................... 5-101
Modbus, close .................................................................................... 5-50
on rear panel ......................................................................................3-12
SNTP, close ....................................................................................... 5-111
TFTP, close ........................................................................................ 5-100
USB ..........................................................................................................4-16
Port number
combinations with protocols ......................................................5-50
connectivity report of those used ............................................4-77
DNP .........................................................................................................5-51
HTTP ........................................................................................................5-99
IEC 60870-5-104 ............................................................................ 5-100
list of .......................................................................................................5-44
Modbus .................................................................................................5-49
Modbus during installation .......................................................... 3-64
RADIUS ..................................................................................................5-18
SNTP .................................................................................................... 5-111
system log ...............................................................................5-18, 5-19
TFTP ..................................................................................................... 5-100
Power metering
specifications .....................................................................................2-28
values .....................................................................................................6-18
Power off, save data first ................................................................3-16
Power supply
description ...........................................................................................3-15
diagram ................................................................................................3-12
LED on module ..................................................................................3-16
removal to replace battery ....................................................... 10-24
specifications .....................................................................................2-30
wire size ................................................................................................3-15
Power swing blocking ........................................................ 2-24, 5-211
Power swing detect
FlexLogic operands ...................................................................... 5-171
logic diagram .................................................................................. 5-216
settings ............................................................................................... 5-209
specifications .....................................................................................2-24
Power system settings .................................................................. 5-143