AGy -L 227
LCD Display DESCRIPTION LCD Selection Description
Def.
Min
Max
Unit
Variat.
IPA
PARAMETER PICK LIST
Code
S.244 Deceleration 2 Linear deceleration with ramp set 2
0.60 0.01 5.00
m/s
2
0.01 332 (F.204)
S.245 Jerk dec end 2 Jerk applied at the end of a deceleration with ramp set 2
1.00 0.01 10.00
m/s
3
0.01 350 (F.258)
S.250 Cont close delay RUN contactor close delay
0.20 0 10 s 0.01 1316
(A.080)
S.251 Magnet time Motor magnetization time
1 0 10 s 0.01 1317
(A.081)
S.252 Brake open delay Brake contactor open delay
0.20 0 10 s 0.01 1318
(A.082)
S.253 Smooth start dly Smooth start duration
0 0 10 s 0.01 1319
(A.083)
S.254 DCBrake stp time Duration of 0Hz braking at stop
1 0 10 s 0.01 1320
(A.084)
S.255 Brake close dly Brake contactor close delay
0.20 0 10 s 0.01 1321
(A.085)
S.256 Cont open delay RUN contactor open delay
0.20 0 10 s 0.01 1322
(A.086)
S.260 Lift stop mode Lift behavior at stop
[0] Dcb at stop DC brake is performed after the
output frequency is below P.440
threshold
101
[1] Normal stop DC brake is not performed at
stop
S.300 Manual boost [%] Manual boost at low revolutions
3.0 0.0 25.0 % of S.100 0.1 421 (P.120)
S.301 Auto boost en Automatic boost function enabling
[0] Disable 0 0 1
[1] Enable
S.310 Slip compensat Amount of slip compensation during motoring
50 0 250 % of
rated slip
1 419 (P.100)
S.311 Slip comp regen Amount of slip compensation during regeneration
50 0 250 % of
rated slip
1 500 (P.102)
S.312 Slip comp filter Time constant of slip compensation
0.3 0 10 s 0.1 420 (P.101)
S.320 DC braking level Current level used during DC brake at start and stop
75 0 100 % of d.950 1 449 (P.300)
S.400 Control mode Drive control mode
[0] V/f OpenLoop Speed control without encoder
feedback
001
[1] V/f ClsdLoop Speed control with encoder
feedback
S.401 Encoder ppr Pulses per revolution of the encoder in use
1024 1 9999 1 151 (I.501)
S.450 Spd ctrl P-gainL Speed loop Proportional gain
2.0 0 100 % 0.1 503 (P.172)
S.451 Spd ctrl I-gainL Speed loop Integral gain
1.0 0 100 % 0.1 504 (P.173)
S.452 Spd PI High lim Speed PI regulator output upper limit
10 0 100 % of F.020 0.1 509 (P.176)
S.453 Spd PI Low lim Speed PI regulator output lower limit
-10 -100 0 % of F.020 0.1 510 (P.177)
S.901 Save parameters Save parameters
(1) (1) (1) (2)
(2)
I.000 Enable src Source of the Enable command of Lift Control Word
[0] False The command is never active 2 0 25 100
[1] True The command is always active
[2] DI 1 The command comes from
DigInp1
[3] DI 2 The command comes from
DigInp2
[4] DI 3 The command comes from
DigInp3
[5] DI 4 The command comes from
DigInp4
1350
(A.220)
423 (P.122)
498 (P.010)
800
(C.000)
INTERFACE
To Next Page
Loading...
