AGy -L 237
LCD Display DESCRIPTION LCD Selection Description
Def.
Min
Max
Unit
Variat.
IPA
PARAMETER PICK LIST
Code
[2] Analog inp 2 Analog input 2
[3] Analog inp 3 Analog input 3
[4] Frequency ref Frequency reference
[5] Ramp output Ramp output
[6] Digital ref Internal reference
[7] Encoder freq Encoder frequency
A.002 PID fbk sel PID feedback selector
[0] Null Null 0 0 7 1202
[1] Analog inp 1 Analog input 1
[2] Analog inp 2 Analog input 2
[3] Analog inp 3 Analog input 3
[4] Encoder freq Encoder frequency
[5] Output curr Output peak current
[6] Output torque Output torque
[7] Output power Output power
A.003 PID digital ref PID digital reference
0 -100 100 % 0.1 1203
A.004 PID activat mode PID active in steady state only
[0] Always 0 0 1 1204
[1] Steady state
A.005 PID-Encoder sync Enabling of encoder / PID synchronism
[0] Disable 0 0 1 1205
[1] Enable
A.006 PID err sign rev Error sign reversal
[0] Disable 0 0 1 1206
[1] Enable
A.007 PIDInteg init en Integral term initialization at start
[0] Disable 0 0 1 1207
[1] Enable
A.008 PID update time PID updating time
0 0 2.5 sec 0.01 1208
A.050 PID Prop gain 1 Proportional term gain 1
0 0 99.99 0.01 1209
A.051 PID Int tconst 1 Integral action time 1
99.99 0 99.99 0.01 1210
A.052 PID Deriv gain 1 Derivative action time 1
0 0 99.99 0.01 1211
A.053 PID Prop gain 2 Proportional term gain 2
0 0 99.99 0.01 1212
A.054 PID Int tconst 2 Integral action time 2
99.99 0 99.99 0.01 1213
A.055 PID Deriv gain 2 Derivative action time 2
0 0 99.99 0.01 1214
A.056 PID high limit PID output upper limit
100 -100 100 % 0.1 1215
A.057 PID low limit PID output lower limit
-100 -100 100 % 0.1 1216
A.058 PID max pos err PID max. positive error
5 0.1 100 % 0.1 1217
A.059 PID min neg err
PID max. negative error
5 0.1 100 % 0.1 1218
A.080 Cont close delay RUN contactor close delay
0.20 0 10 s 0.01 1316
A.081 Magnet time Motor magnetization time
1 0 10 s 0.01 1317
A.082 Brake open delay Brake contactor open delay
0.20 0 10 s 0.01 1318
A.083 Smooth start dly Smooth start duration
0 0 10 s 0.01 1319
A.084 DCBrake stp time Duration of 0Hz braking at stop
1 0 10 s 0.01 1320
A.085 Brake close dly Brake contactor close delay
0.20 0 10 s 0.01 1321
A.086 Cont open delay RUN contactor open delay
0.20 0 10 s 0.01 1322
A.087 Current pres thr Current threshold for inverter output phases check
10 0 100 % 1 1325
A.088 Sel match code Code to be compared to the status of Freq selectors
0 0 15 1326
A.090 Car max speed Speed of the lift car when the inverter output frequency is equal
to P.062
0.50 0.01 5.00 m/s 0.01 1323
A.091 Ramp factor 1 multiplier for acc/dec and jerks of ramp sets 1 and 3
1.00 0.01 2.50 0.01 1324
A.092 Ramp factor 2 multiplier for acc/dec and jerks of ramp sets 2 and 4
1.00 0.01 2.50 0.01 1327
A.220 Lift stop mode Lift behavior at stop
[0] Dcb at stop DC brake is performed after the
output frequency is below P.440
threshold
1 0 1 1350
[1] Normal stop DC brake is not performed at
stop
A.300 AND1 In 1 src Source of In 1 of logic block AND1
see list of I.000 0 0 25 1355
A.301 AND1 In 2 src Source of In 2 of logic block AND1
see list of I.000 0 0 25 1356
A.302 AND2 In 1 src Source of In 1 of logic block AND2
see list of I.000 0 0 25 1357
A.303 AND2 In 2 src Source of In 2 of logic block AND2
see list of I.000 0 0 25 1358
A.304 AND3 In 1 src Source of In 1 of logic block AND3
see list of I.000 0 0 25 1359
A.305 AND3 In 2 src Source of In 2 of logic block AND3
see list of I.000 0 0 25 1360
A.306 OR1 In 1 src Source of In 1 of logic block OR1
see list of I.000 0 0 25 1361
A.307 OR1 In 2 src Source of In 2 of logic block OR1
see list of I.000 0 0 25 1362
A.308 OR2 In 1 src Source of In 1 of logic block OR2
see list of I.000 0 0 25 1363
A.309 OR2 In 2 src Source of In 2 of logic block OR2
see list of I.000 0 0 25 1364
A.310 OR3 In 1 src Source of In 1 of logic block OR3
see list of I.000 0 0 25 1365
A.311 OR3 In 2 src Source of In 2 of logic block OR3
see list of I.000 0 0 25 1366
A.312 NOT1 In src Source of Input of logic block NOT1
see list of I.000 0 0 25 1367
A.313 NOT2 In src Source of Input of logic block NOT2
see list of I.000 0 0 25 1368
A.314 NOT3 In src Source of Input of logic block NOT3
see list of I.000 0 0 25 1369
A.315 NOT4 In src Source of Input of logic block NOT4
see list of I.000 0 0 25 1370
To Next Page
Loading...
