Need help?Do you have a question about the GILBARCO VEEDER-ROOT FlexPay IV CRIND and is the answer not in the manual?
General| Model | FlexPay IV CRIND |
|---|---|
| Category | Payment Terminal |
| Manufacturer | GILBARCO VEEDER-ROOT |
| Security | PCI PTS 5.x certified |
| Operating System | Linux-based |
| Connectivity | Ethernet |
| Payment Methods | Contactless Payments |
| Display | Color LCD |
| Power Supply | 100-240 VAC, 50-60 Hz |
| Dimensions | Varies depending on configuration |
| Weight | Varies by configuration |
| Card Reader | EMV Chip |
Outlines the manual's objective to install a retrofit kit in specific dispenser models.
Identifies the target audience as trained and certified service contractors.
Lists all tools necessary for performing installation tasks.
Details the standard components included in a typical retrofit kit.
Lists additional parts that may be included based on kit configuration.
Provides a detailed breakdown of all kit parts with part numbers and notes.
General safety precautions and hazards associated with servicing fueling equipment.
Emphasizes working in hazardous environments and the need for trained personnel.
Crucial instructions on how to perform an emergency electrical shutdown.
Mandates powering down equipment before accessing electrical components.
Outlines site preparation and safety measures before commencing work.
Stresses the importance of understanding all provided documentation for safety.
Highlights compliance with NFPA, NEC, OSHA, and local codes.
Advises using only genuine manufacturer replacement parts to ensure safety.
Provides FCC compliance information for digital devices and potential interference.
Explains the meaning of safety alert symbols and signal words used in the manual.
Details hazards related to flammable fuels, vapors, and electrical energy.
Warns about potential health hazards and necessary precautions when handling materials.
Provides critical information for reporting and handling emergencies involving personnel.
Explains the procedures for controlling hazardous energy sources during maintenance.
Prepares the user with essential checks and safety procedures before removing parts.
Guides the removal of specific TRIND and call button components.
Details the steps to disconnect and remove the door node assembly.
Instructions for removing the printer assembly from the old door.
Steps for safely detaching and removing the Customer Interface Module (CIM) door.
Procedure for removing the Underwriters Laboratories (UL) bucket.
Specific instructions for removing CRIND components on Encore 300 models.
Covers removal procedures for Encore 500 models with specific CRIND types.
Steps to remove the CRIND Control Node (CCN) or Hub Interface PCB (HIP) assembly.
Instructions for removing the AFP, HIP 2, DCM2, or DCM2.1 bracket.
Introduction to the installation process for the FlexPay IV CRIND retrofit kit.
Steps for installing the new Customer Interface Module (CIM) door.
Instructions for mounting the AFP/DCM2 assembly onto the T-rail.
Details on installing the DCM2 board, its functionality, and connections.
Connecting various cables and configuring jumpers for the DCM2 assembly.
Procedures for installing the DCM2.1 assembly and updating software.
Steps for installing the DCM2.2 assembly and its components.
Illustrates the cable routing for the Applause Media System.
Instructions for installing or remounting the UL bucket using offset brackets.
Explains different power supply scenarios and connection methods for AFP/DCM2.
Specifics on installing ICE or Phoenix power supplies for Encore 500 models.
Details on connecting the 24 V power to the printer based on the power supply type.
General guidance on communication wiring for AFP/DCM2.
Block diagram and chart for two-wire communication setup.
Instructions for mounting and connecting the intercom interface board.
Final inspection of connections, cable routing, and closure of doors.
Procedure for registering installed kits to ensure warranty coverage.
Lists other relevant manuals and documentation for further reference.
Provides definitions for technical terms and acronyms used in the manual.
Details various optional peripheral devices that can be installed.
Instructions for installing the optional cabinet heater for display protection.
Specifics on the intercom option, its function, and block diagram.
Information regarding the UPM heater installation and related documents.
Guidance for installing the call button option and related manual.
Visual representations of cable connections and system configurations.
Guidance and examples for verifying correct cable connections.
Illustrates cable routing and connections on the display assembly.
Details on how power cables should be connected to various boards.
Specific instructions for cabling the PIP3 board.
Instructions for connecting cables to the Universal Payment Module (UPM).
Steps for connecting the intercom system components.
Instructions for connecting cables to the UX300 card reader.
To Next Page
