CE5000-UM-251-9370 ii
HISTORY OF REVISIONS
No. Date issued Description of revision Page Edition
1 06.07.06 First Printing All 01
2 0 6.09.13 Information for the 9e60p was added. 10 -1,10-12 02
3 0 6.09.13 Part list for the steel stand ST0068 was added. 10-9 02
4 0 6.09.13
Part number for the main board of the CE5000-40 was corrected.
4-1,10-1 02
5 06.09.26 Procedure of upgrading the system firmware was corrected. 7-13 03
6 06.09.26 Section numbers were corrected. 11-10 to 11-12 03
7 0 6.11.07 Procedure of adjusting the pen force was corrected. 7-4 04
8 0 6.11.16 Hooter of page was wrong. 4-1 05
9 0 6.11.16 Cutting Mat 40 of part number was updated. 4 -1,10 - 3 05
10 0 6.11.16 Cutting Mat 120 of part number was updated. 4-1,10 - 3 05
11 07. 02. 28 Part number for the cutter pen holder was corrected. 10-6 06
12 07. 02. 28
The cutter pen holder and the pen holder thumb screw L10 were deleted from recommended parts list.
4-1 06
13 07.0 5.18 CE5000-120AP information added. All 07
14 07.10.19
Remark of the Main Board of CE5000-120AP was corrected.
4-1 08
15 08.03.04 Description for the roll stocker was corrected. 10 -15 09
16 08.08.22
Procedure of adjusting the Auto-Registration Mark Sensor Sensitivity was added.
7-10 10
17 0 8.10. 28 Rank of parts were corrected. 10-1 to 10-16 11
18 08.11.04 X and Y motor cables were added to the parts list. 10-9 12
19 08.12.15
Part number for the Auto registration mark sensor was corrected.
4 -1,10 -7 13
20 08.12.15
The X-drive belt for CE5000-40 and -60 were changed.
10-3 13
21 0 8.12.15
The replacing procedure was added for the X-drive belt of the CE5000-40 and the CE5000-60.
6-27 13
22 08.12.15 Part number was added for the stopper assembly. 10 -12 13
23 09.01.09 Procedure of the distance adjustment was corrected. 7-7 14
24 09.04.02 Part number for the stock shaft was corrected. 10-10,10-11 15
25 09.04.02 Part number for the stopper was corrected. 10-10 15
26 09.04.02 The explanation of the sensor status were corrected. 8-1 15
27 09.08.24 Part number for the Y drive pulley was corrected. 4 -1,10 - 3,10 - 5 16
28 09.08.24
Part number for the rubber spacer of CE5000-120AP was corrected.
10-5 16
29 11.03.02 The item No.38 was not including the item No.37. 10-5 17
30 11.03.03
The replacing procedure added for the new type of main board.
18
31 11.03.03 The parts number added for the new type of main board. 4-1,10-1 18
32 11.03.04
The Dip Switch setting added for the new type of main board.
7-1 18
33 11.03.07 The circuit diagrams added for the new type of main board. 11-13 to 11-18 18
34 11.03.07 Confirmation for the Y rail mounting position is added. 6-38 to 6-40 18
35 11.03.07 The adjusting procedure added for the drive roller height. 6-41 to 6-43 18
36 11.0 5.16
The dip-switch setting for the NV-RAM Clear of new type of main board was corrected.
7-1,7-4 19
37 11.05.16
The menu and procedure were corrected for updating the firmware of new main board.
7-16 19
38 11.0 5.16
The procedure was corrected for replacing the new type of main board .
6-34 19
39 11.08.01 The parts number of LCD changed. 4-1,10-1 20
40 11.10.11 The baearing added for the CE5000-120AP-AMJ 10-5 21
41 11.10.11 The parts number changed for the rubber spacer. 10-5 21
42 11.10.11 The parts number added for the new type of main board. 10-6 21
43 12.01.06 The measuring position of pen block height was added. 6-16 21
44 12.11.22 Part number for the tension spring was corrected. 10-5 22
45 12.11.22 Part number for the center bar 120AP was corrected. 10 -13 22
46 13.02.20 Part number for the Push Roller was corrected. 4 -1,10 - 3,10 - 5 22
47 13.02.20 Part number for the Y Belt 40 was corrected. 4 -1,10 -7 22
48 13.02.20 Part number for the Y Belt 60 was corrected. 4-1,10 -7 22
49 13.02.20 Part number for the Y Belt 120 was corrected. 4 -1,10 -7 22
50 13.02.20
Part number for the Push Roller Sensor Flexible Cable was corrected.
4 -1,10 -7 22
51 13.02.20
Part number for the X Motor for CE5000-40/60 was corrected.
4 -1,10 - 3 22
52 13.02.20
Part number for the Y Motor for CE5000-40/60/120 was corrected.
4 -1,10 - 3,10 - 5 22
53 13.02.20
Part number for the Control Panel Switch Sheet was corrected.
4-1,10-1 22
To Next Page
Loading...
