H3C S5560X-EI Series - User Manual

Other manuals for H3C S5560X-EI Series

Configuration Guide63 pages

Command Reference59 pages

Questions and Answers

L
Lisa SchultzJul 28, 2025
How to troubleshoot AC input failure on H3C Switch?
- J
  Jason NelsonJul 28, 2025
  To troubleshoot an AC input failure on your H3C Switch, take these steps: 1. Check that the AC power cord is properly connected between the switch and the AC power source, and that both the switch's AC power receptacle and the AC power outlet are in good condition. 2. Confirm that the AC power source is functioning correctly. 3. Ensure the switch's ambient temperature is within the acceptable range and that the power module has good ventilation. Overheating can cause the power module to shut down as a protective measure.
B
Bradley MoranAug 4, 2025
What to do if there is RPS input failure on H3C S5560X-EI Switch?
- M
  Michael JohnsonAug 4, 2025
  If you're experiencing an RPS input failure with your H3C Switch, try the following: * First, verify that the switch is correctly connected to the RPS. * Next, confirm that the RPS is operating correctly. * Also, ensure that the ambient temperature of the switch is within the acceptable range and that the power module has sufficient ventilation, as overtemperature can cause the power module to stop working.
T
Tammy HarmonAug 11, 2025
What to do if there is no display on PC when using H3C Switch?
- S
  Suzanne RangelAug 11, 2025
  If you're experiencing a blank screen when trying to connect to your H3C Switch, there are a few things you can check: * First, make sure the power module is properly supplying power to the switch. * Next, verify that the console cable is correctly connected. * Also, ensure the console cable itself is working correctly and that your PC settings are properly configured.
B
Brian EdwardsAug 19, 2025
How to fix garbled display on PC when using H3C S5560X-EI Switch?
- M
  Michael FigueroaSep 12, 2025
  If you are seeing a garbled display on your PC when connected to the H3C Switch, verify that your terminal settings are configured as follows: Baud rate—9,600, Data bits—8, Stop bits—1, Parity—None, Flow control—None.

Summary

Preface

Audience

Intended users of the product documentation.

Conventions

Describes syntax and GUI conventions used in the documentation.

Symbols

Network topology icons

Visual representations of network devices and signals used in diagrams.

Documentation feedback

Preparing for installation

Safety recommendations

Essential safety guidelines to prevent injury and equipment damage during installation.

Examining the installation site

Criteria for selecting a suitable indoor installation environment for the switch.

Temperature;humidity

Recommended temperature and humidity levels for optimal switch operation.

Cleanliness

Dust and environmental contamination limits for equipment rooms to prevent issues.

EMI

Guidelines to prevent electromagnetic interference affecting the switch performance.

Laser safety

Safety precautions regarding laser light emitted from fiber optic ports.

Installation tools

List of user-supplied tools required for switch installation.

Installing the switch

Installing the switch in a 19-inch rack

Step-by-step procedures for mounting the switch in a standard rack.

Mounting the switch on a workbench

Instructions for safely placing and securing the switch on a workbench.

Grounding the switch

Importance and methods for grounding the switch for safety and EMI protection.

Installing;removing a fan tray

Procedures for installing and removing fan trays for proper cooling.

Installing;removing a power module

Steps for installing and removing power modules for power supply.

Connecting the power cord

How to connect power cords to various types of power modules.

Installing;removing an expansion card

Procedures for installing and removing expansion cards for added functionality.

Verifying the installation

Checks to perform after the switch installation is complete.

Rack-mounting the switch by using front mounting brackets

Detailed instructions for rack mounting using front brackets.

Installation accessories

List of included accessories for switch installation.

Rack-mounting the switch by using front and rear mounting brackets

Detailed instructions for rack mounting using front and rear brackets.

Grounding the switch with a grounding strip

Connecting the switch to a grounding strip for safety.

Grounding the switch with a grounding conductor buried in the earth ground

Grounding the switch using an earth ground conductor.

Installing a fan tray

Step-by-step guide for installing a fan tray into the switch.

Removing a fan tray

Step-by-step guide for removing a fan tray from the switch.

Installing a PSR150-A1;PSR150-A2;PSR150-D1 power module

Procedure for installing specific PSR150 power modules.

Installing a PSR360-56 A;PSR560-56 D;PSR720-56 A;PSR1110-56 A power module

Procedure for installing specific PSR360/560/720/1110 power modules.

Removing a PSR150-A1;PSR150-A2;PSR150-D1 power module

Procedure for removing specific PSR150 power modules.

Removing a PSR360-56 A;PSR560-56 D;PSR720-56 A;PSR1110-56 A power module

Procedure for removing specific PSR360/560/720/1110 power modules.

Connecting the power cord for the built-in AC power module

Steps to connect the AC power cord to the switch's AC power module.

Connecting a power cord for the built-in DC power module

Steps to connect the DC power cord to the switch's DC power module.

Connecting the PSR150-A1;PSR150-A2

Procedure for connecting power cords to PSR150-A1/A2 power modules.

Connecting the PSR150-D1;PSR560-56 D

Procedure for connecting power cords to PSR150-D1/PSR560-56D power modules.

Connecting the PSR360-56 A;PSR720-56 A;PSR1110-56 A

Procedure for connecting power cords to PSR360/720/1110 power modules.

Installing an expansion card

Step-by-step guide for installing an expansion card into the switch.

Removing an expansion card

Step-by-step guide for removing an expansion card from the switch.

Accessing the switch for the first time

Setting up the configuration environment

Preparing the PC and connection for initial switch configuration.

Connecting the serial console cable

Connecting the switch to a PC using a serial console cable.

Connecting the micro USB console cable

Connecting the switch to a PC using a micro USB console cable.

Setting terminal parameters

Required terminal emulator settings for console connection.

Powering on the switch

Pre-power-on checks and the procedure for powering on the switch.

Setting up an IRF fabric

IRF fabric setup flowchart

Visual overview of the steps involved in setting up an IRF fabric.

Planning IRF fabric setup

Key considerations and planning steps for an IRF fabric setup.

Planning IRF fabric size and the installation site

Determining the required IRF fabric size and selecting the installation site.

Identifying the master switch and planning IRF member IDs

Selecting the master switch and assigning unique IDs to member switches.

Planning IRF topology and connections

Designing the network topology and planning physical connections for IRF.

Identifying physical IRF ports on the member switches

Selecting appropriate physical ports on member switches for IRF connections.

Planning the cabling scheme

Choosing appropriate cables for connecting IRF member switches.

Configuring basic IRF settings

Initial configuration steps for IRF member switches.

Connecting the physical IRF ports

Making the physical connections between IRF member switches.

Verifying the IRF fabric setup

Confirming the successful setup and functionality of the IRF fabric.

Maintenance and troubleshooting

Fixed power module failure

Troubleshooting steps for fixed power module failures.

Hot-swappable power module failure

Troubleshooting steps for hot-swappable power module failures.

Fixed fan tray failure

Troubleshooting steps for fixed fan tray failures.

Hot-swappable fan tray failure

Troubleshooting steps for hot-swappable fan tray failures.

Configuration terminal display problems

Resolving issues where the terminal displays no output or garbled text.

Appendix A Chassis views and technical specifications

Chassis views

Visual identification of front and rear panels for various switch models.

Technical specifications

Detailed technical specifications for non-PoE switch models.

S5560 X-30 C-PWR-EI Chassis

Visual identification of front and rear panels for the S5560X-30C-PWR-EI model.

S5560 X-54 C-EI Chassis

Visual identification of front and rear panels for the S5560X-54C-EI model.

S5560 X-54 C-PWR-EI Chassis

Visual identification of front and rear panels for the S5560X-54C-PWR-EI model.

S5560 X-30 F-EI Chassis

Visual identification of front and rear panels for the S5560X-30F-EI model.

S5560 X-54 F-EI Chassis

Visual identification of front and rear panels for the S5560X-54F-EI model.

S5560 X-34 S-EI Chassis

Visual identification of front and rear panels for the S5560X-34S-EI model.

S5560 X-54 S-EI Chassis

Visual identification of front and rear panels for the S5560X-54S-EI model.

Appendix B FRUs and compatibility matrices

Hot-swappable power modules

Details on power modules that can be replaced while the switch is operating.

Hot-swappable fan trays

Details on fan trays that can be replaced while the switch is operating.

Expansion cards

Information on available expansion cards and their specifications.

Connecting cables to the copper ports on the interface cards

Guidelines for connecting copper cables to interface card ports.

Appendix C Ports and LEDs

Ports

Description of physical ports including console, Ethernet, SFP, SFP+, QSFP+.

LEDs

Explanation of various status LEDs: System, Power, RPS, Mode, Port, Expansion Card, Fan Tray.

Appendix D Cooling system

Airflow through the switch with fixed fan trays

Description of airflow for switches with fixed fan trays.

Airflow through the switch with hot-swappable fan trays

Description of airflow for switches with hot-swappable fan trays.

H3C S5560X-EI Series Specifications

General

Brand	H3C
Model	S5560X-EI Series
Category	Switch
Language	English

Related product manuals