HCS DAC-42A - Page 67

DAC-42(A)-x-PN
Page 67
DAC-42(A)-x-PN Manual
Revision: 1.0 22.01.2024
ID
Hex
ID
dec
W/R
Nam
e
Function Unit Min Max Def Description
0x69 105 R/W E10
E1.10
Solenoid current adaptation A --- 50 110 100 Variable adjustment of max. current
100 == Factor 1.00
0x6A
106
R/W
E11
Initial current solenoid A
V
0
9999
0
3.000 V = 30 % of max. rated current
0x6B
107
R/W
E12
Initial current solenoid B
V
0
9999
0
0x6C 108 R/W E13
E1.13
Dither Amplitude A V 0 3000 0
0x6D 109 R/W E14
E1.14
Dither Frequency A Hz 1 300 0 ---
0x6E 110 R/W E15 Selection set point S1.06 (U/I) --- 0 11 1 off = Deactivated
1 = Voltage -10V..+10V
2 = Voltage 0..10V
3 = Voltage 5V+-5V
4 = Voltage 5V+-4.5V w/o signal observation
5 = Voltage 5V+-4.5V with signal observation
6 = 0..20mA w/o cable fract. det.
7 = 10+-10mA w/o cable fract. det.
8 = 4..20mA w/o cable fract. det.
9 = 4..20mA with cable fract. det.
10 = 12+-8mA w/o cable fract. det.
11 = 12+
-
8mA with cable fract. det.
0x6F
111
R/W
E16
Reserved
---
---
---
---
---
0x70 112 R/W E17 Set value activation mode --- 0 3 off off = 4 digital, 3 analog active
1 = 5 digital SP, 3 analog active
2 = only 4 digital active
3 = only 5 digital active
0x71 113 R/W E18
Error / Comparator output selection
Modus 1,2
--- off 1 off off = break off
1 = break on
Modus 3,4,10,11 --- off 5 off off = break off, comp. positive logic
1 = break on, comp. positive logic
2 = break follows comp. positive logic
3 = break not and comp. positive logic
4 = break and comp. negative logic
5 = break not and comp neg. logic
Modus 6,8 --- off 13 off off = break off, comp. positive logic
1 = break on (supply) comp. pos. log
2 = break follows comp., comp. pos. log
3 = break log. not comp., comp. pos. log
4 = break log. not comp., comp. neg. log
5 = break a. comp. same, comp. neg. l.
6 = break follow Comp1, comp. pos. log
7 = break log. not Comp1, comp. pos. l.
8 = break log. not Comp1, comp. neg. l.
9 = break a. Comp1 same, comp. neg. l.
10 = break follow Comp2; comp. pos. l.
11 = break log. not Comp2, comp. pos. l.
12 = break log. not Comp2; comp. neg. l.
13 = break a. Comp2 same, comp. neg. l
0x72 114 R/W E19 Factor for analog output
(depends on HW + SW version)
V/V -400 400 100 100 == Factor 1.00
Sign
and
gain!
0x73
115
X
E20
Reserved
---
---
---
---
..
..
0xA2
162
X
---
Reserved
---
---
---
---
0xA3 163 R/W E 22 Profinet Slave Address --- 0 32 0 0 = No bus function
1 = Standard Profinet
2..5 = Multiple Slave Profinet
0xA4
164
R/W
C1.27
Hysteresis command A
V
-
9999
9999
0
-1000 == -1.000 V; 1000 == 1.000 V
0xA5
165
R/W
C2.27
Hysteresis command B
1
-
9999
9999
0
0xA6
166
X
---
Reserved
---
---
---
---
0xA7
167
X
---
Reserved
---
---
---
---
0xA8
168
X
---
Reserved
---
---
---
---
0xA9
169
X
---
Reserved
---
---
---
---
0xAA
170
X
---
Reserved
---
---
---
---
0xAB
171
X
---
Reserved
---
---
---
---
0xAC
172
X
---
Reserved
---
---
---
---
0xAD
173
X
---
Reserved
---
---
---
---
0xAE
174
X
---
Reserved
---
---
---
---
0xAF
175
X
---
Reserved
---
---
---
---