Honeywell GasAlert Max XT II User Manual

Name: Honeywell GasAlert Max XT II
Brand: Honeywell
Rating: 4 (1 reviews)

81 pages

To Next Page

To Previous Page

GasAlertMaxXT II

User Manual

If a sensor(s) fails any step of the calibration, the following screen

displays.

Note

If calibration is unsuccessful for a sensor(s), the calibration due

date cannot be set for the failed sensor(s).

Calibration Due Date

If a sensor(s) does not successfully span, the calibration due date for

that sensor(s) will not reset.

Default Chapter3
- Table of Contents3
Title Page4
Contacting BW Technologies by Honeywell13
Introduction13
- Gases Monitored14
Safety Information - Read First14
Getting Started19
Parts of the Gasalertmaxxt II20
Display Elements21
Activating/Deactivating the Detector23
Startup Tests23
- Battery Test23
- Audible/Visual Test23
- Pump Test on Startup25
- Alarm Setpoints26
- Self-Test27
- Automatic Zero for H S, CO, O , and LEL28
- If Previous Calibration Failed28
- Calibration Due Date (Optional)29
- Force Calibration Enabled (Optional)29
- Cal IR Lock Enabled (Optional)30
- If Previous Bump Failed30
- Bump Test30
- Force Bump Enabled (Optional)31
- Startup Test Pass31
- Startup Test Fail32
Title30
Installing Fleet Manager II33
- Using Fleet Manager II to Configure the Detector33
Device Configuration34
- Serial Number Field35
- Firmware Version35
- Hardware Version35
- Startup Message Top Line35
- Startup Message Bottom Line35
- Lockout on Self-Test Error (Failed Sensor Lock)35
- Safe Mode36
- Confidence Beep36
- Latching Alarms36
- Force Calibration36
- Force Bump37
- Cal IR Lock37
- Location Logging38
- Force Block Test38
- Datalog Interval38
- Confidence Interval39
- Language39
Sensor Configuration39
- Sensor Disabled40
- Calibration Gas (Ppm)40
Title41
- Calibration Interval41
- Bump Interval41
- Low Alarm41
- High Alarm41
- TWA Alarm42
- STEL Alarm42
- STEL Interval43
- TWA Period (Hours)43
- Correction Factor (%)43
- 50% Lel = (%Ch4)44
- Auto Zero on Startup44
- LEL by Volume CH444
- 10% (of Reading) Over-Span44
- 20.8 Base Reading44
- Low Alarm Acknowledge44
Alarms45
Computed Gas Exposures48
- Viewing and Clearing Gas Exposures48
- Gas Alarm Setpoints49
- Resetting Gas Alarm Setpoints50
- Stopping a Gas Alarm50
- Sensor Alarm50
- Pump Alarm51
- Low Battery Alarm51
- Automatic Deactivation Alarm51
Bump Test52
- Bump Test Using the Microdock II Station52
Title53
Calibration53
- Guidelines53
- Diagnostics Protection54
- Connecting the Gas Cylinder to the Detector54
- Calibration Procedure55
- Calibrating Using the IR Link60
Event Logs62
Datalogs62
Bump and Calibration Results63
- Downloading Datalogs and Event Logs63
- Software Requirements63
Maintenance64
- Maximum Hose Length for Sampling64
- Battery Maintenance and Cautions64
- Charging the Battery65
  - Optimum Battery Operation66
- Replacing the Battery66
- Replacing a Sensor or Sensor Filter66
- Replacing the Pump Filters70
- Replacing the Pump72
Troubleshooting73
Replacement Parts and Accessories76
Specifications78

Questions and Answers:

Need help?

Do you have a question about the Honeywell GasAlert Max XT II and is the answer not in the manual?

Honeywell GasAlert Max XT II Specifications

General

Brand	Honeywell
Model	GasAlert Max XT II
Category	Security Sensors
Language	English

Related product manuals

Honeywell XT Series

28 pages

Honeywell GENT S-Quad S4-720

4 pages

Miller Twin Turbo G2 Connector

Honeywell Minipeeper C7027A

12 pages

Miller TurboLite Series

268 pages

Honeywell GasAlert Max XT II User Manual

Table of Contents

Questions and Answers:

Honeywell GasAlert Max XT II Specifications

Related product manuals