Format of Possible cabling Exception Messages
Cabling <cageID> "Cabled to <nodelist>, remove a cable from <nodelist>"
Cabling <nodeID> "No cabling data for <nodeID>. Check status of <nodeID>"
Cabling <cageID> "Cage is connected to too many node ports (<portlist>)"
Cabling <cageID> "Cage has multiple paths to <portlist>, correct cabling"
Cabling <cageID> "I/O <moduleID> missing. Check status and cabling to <cageID> I/O <moduleID>"
Cabling <cageID> "Cage not connected to <nodeID>, move one connection from <nodeID> to <nodeID>"
Cabling <cageID> "Cage connected to different ports <node&portID> and <node&portID>"
Cabling <cageID> "Cage connected to non-paired nodes <node&portID> and <node&portID>"
Cabling <cageID> "Check connections or replace cable from (<cage,module,portID>) to (<cage,module,portID>) - failed links"
Cabling <cageID> "Check connections or replace cable from (<cage,module,portID>) to (<cage,module,portID>) - links at
<speed>"
Cabling <nodepairID> "<node&portID> has <count> cages, <node&portID> has <count> cages"
Cabling <cageID> "Cable in (<cage,module,portID>) should be in (<cage,module,portID>)"
Cabling <cageID> "No PDs installed in cage, cabling check incomplete"
Cabling <cageID> "<node&portID> has <count> cages connected, Maximum is <count> (<cagelist>)"
Cabling <cageID> "<node&portID> should be cabled in the order: (<cagelist>)"
cabling Example 1
Component -Summary Description- Qty
Cabling Bad SAS connection 1
Component -Identifier- ----------------------------------------Detailed Description-----------------------------------------
Cabling cage7 Check connections or replace cable from (cage6, I/O 0, DP-2) to (cage7, I/O 0, DP-1) - links at
6Gbps
cabling Suggested Action 1
Use the CLI showcage command to verify that both cages are available through two ports, before
replacing the cable specified in the error message.
cli% cli% showcage cage6 cage7
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model FormFactor
6 cage6 3:0:4 1 2:0:4 0 10 28-30 1.76 1.76 DCS4 SFF
7 cage7 3:0:4 0 2:0:4 1 10 27-30 1.76 1.76 DCS4 SFF
cabling Example 2
Cabling
checkhealth -detail cabling
Checking cabling
Component --Summary Description--- Qty
Cabling Wrong I/O module or port 2
--------------------------------------
1 total 2
Component -Identifier- ---------------------Detailed Description----------------------
Cabling cage2 Cable in (cage2, I/O 0, DP-2) should be in (cage2, I/O 0, DP-1)
Cabling cage2 Cable in (cage2, I/O 0, DP-1) should be in (cage2, I/O 0, DP-2)
--------------------------------------------------------------------------------------
2 total
root@jnodec103288:~# showcage cage2
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model FormFactor
2 cage2 1:0:2 1 0:0:2 0 10 13-34 402e 402e DCS1 LFF
cabling Suggested Action 2
For cables that should be moved to different ports in the same I/O module: Use the CLI showcage
command to verify that the cage is available through two ports, before moving the cable(s) to the
specified ports. For cables that should be moved between different I/O modules and/or cages,
contact HP support to request support for changing the cabling of your system. See “Contacting
HP Support about System Setup” (page 73). Moving cables on a running system can cause
degraded PDs and LDs.
cli% showcage cage2
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model FormFactor
2 cage2 1:0:2 1 0:0:2 0 10 13-34 402e 402e DCS1 LFF
38 Troubleshooting
To Next Page
Loading...
