HySecurity StrongArm 14F - Strongarm HTG Loop Layout

HySecurity StrongArm 14F

134 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

MX3657-01 Rev. D ©2020

98 hysecurity.com | 800-321-9947 StrongArm Programming and Operations

stronGarM htG looP layout

Table of Contents

C Ontents3
- Table of Contents3
S Trong a Rm I Nstallation O Verview7
Strongarm Components8
Strongarm Pump Pack Components9
Important Safety Instructions11
- Important Safety Information12
- Proper Grounding and Breather Cap Installation21
- Manual Release: Manual Bypass Valve22
Installation23
- Installation Preparation Checklist23
Power29
- Installing the Earth Ground29
  - Site Considerations30
- Wiring AC Power30
  - Turning the Power Switch on31
- Wire Sizing and Runs32
  - Low Voltage Control Wiring32
  - Strongarm Wiring Charts (Incoming Power)33
- Control Transformer Connections (Non-UPS)35
- Gate Operator Connections (Modular Unit)35
- DC Power Supply (UPS) Connections36
- AC Power Supply with Hyinverter AC36
Initial Setup37
- Replace the Red Vent Plug with the Breather Cap38
- Learn When and What to Adjust38
- Leveling and Balancing Arm39
- Strongarm Counterweights Installation40
- Strongarmdot 28 Break-Away Arm Installation42
- Valve Adjustments44
  - Adjust Pressure Relief Valve44
  - Adjusting Brake Valve44
- Limit Switch Adjustments45
- Emergency Override46
  - Manual Bypass Valve46
  - Cycle Test the Arm46
- Emergency Fast Close47
- Installing a Push Button Device for Emergency Fast Operate (EFO)47
Entrapment Protection49
- Table 4: Hysecurity Gate Operators Maintaining Object Detection50
- Supply Power to the Sensors51
- External Entrapment Protection52
- Photo Eye Function53
Control Panel Overview55
- Strongarm Wiring Diagram56
- Limit Switches56
- STC Board, Power Supply Board and Display57
Display & Menu Options59
- Initial Setup59
- Understanding the Display and Keypad59
- Menu Mode and the STC Keypad60
- Menu Mode Navigation60
- Run Mode and the STC Keypad61
- Viewing Gate Operator Scrolling Status61
- User Menu63
- User Menu: Table 564
- Installer Menu66
- Installer Menu: Table 666
- Setting the Close Timer73
- Test the Operator74
STC Inputs & Wiring75
- Overview of the STC and Power Supply Board76
- Integrating with Security Systems and Hynet™ Gateway77
- Smart Touch Controller Inputs78
- STC Terminal Inputs78
- Connecting Accessory Devices79
- User Relays - Programming Procedure81
- Programmable User Relays: Table 781
- Hy8Relay Module Option84
Bi-Parting & Dual Gate Systems85
- Connecting an Interlocked Pair (Dual Gate)85
- Connecting Sequenced Gates88
- Sequenced Gate: Configuration #190
- Sequenced Gate: Configuration #291
Ehicle D Etector I Nstallation93
- Anti-Tailgate Mode (Closing Logic)93
- Tailgate Alert93
- Vehicle Detector Installation: Hy5A and Hy5B94
- Connecting Hy5A Vehicle Detectors95
  - View Call Level in Real Time96
- Installing Standard 11-Pin Box Type Vehicle Detectors97
- Strongarm HTG Loop Layout98
Photo Eye Installation99
- Photo Eyes (Non-Contact) Installation100
- Retro-Reflective Photo Eye Systems102
  - Using Photo Eye Sensors Instead of Vehicle Loops103
  - Photo Eye Alignment Feature104
Troubleshooting105
- System Diagnostic Messages105
- Typical Problems and Troubleshooting Procedures106
- Troubleshooting Codes: Table 8107
- Access the Event Log through the User Menu112
- Electrical Issues113
  - AC-Powered Gate Operators113
- Mechanical Issues114
- Hydraulic Issues114
General Maintenance115
- Smart Touch Analyze and Retrieve Tool (S.T.A.R.T.)115
  - What You Need115
  - Installing S.T.A.R.T. Software115
- Software Maintenance116
- Electrical Controls116
  - Clock Battery Replacement116
- Mechnical Controls117
  - Stopping the Gate117
  - Starting the Gate117
- Mechanical Maintenance117
- Hydraulic System Maintenance118
- Strongarm Operator Maintenance Schedule120
Iring H y S Ecurity S Ensors : S Mart T Ouch121
- Wiring Tips for SENSOR COM Terminal: Smart Touch122
- Menu Mode Navigational Tips122
- Smart Touch: Wired Edge Sensor with GEM (-104)123
- Smart Touch: Photo Eye Thru Beam (EMX IRB MON)124
- Smart Touch: Photo Eye / Reflective (E3K R10K4)125
- Smart Touch: the Solution, MIM-62 (Multi-Input Module)126
- Smart Touch: Photo Eye / Reflecti-Guard (RG-R)127
- Smart Touch: Wireless Edge, Wireless Gate Link128
- Smart Touch: Wired Edge with GEM-104 & Photo Eye129
- Smart Touch: Wireless Edge Gate Link & Photo Eye130
- Strongarm Installer Checklist131
Arranty133
Specifications134

Related product manuals

Preview: HySecurity StrongArmPark DC 10

HySecurity StrongArmPark DC 10

HySecurity StrongArmPark DC 14

HySecurity StrongArmPark DCS 14

HySecurity SlideDriver 40

Preview: HySecurity SlideDriver 15

HySecurity SlideDriver 15

HySecurity SlideDriver 30F

Preview: HySecurity SlideSmart DC 15

HySecurity SlideSmart DC 15

Preview: HySecurity SwingSmart DC 20

HySecurity SwingSmart DC 20

Preview: HySecurity SlideDriver 50VF2

HySecurity SlideDriver 50VF2

Preview: HySecurity SlideSmart DCS 15

HySecurity SlideSmart DCS 15

HySecurity SlideDriver 50VF2/3

Preview: SlideDriver 50 VF Series

SlideDriver 50 VF Series