Icom i9100

118
8
DV MODE OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
■ DV Set mode description
The DV Set mode is used for programming infrequently
changed values or functions in the DV mode.
D DV Set mode settings
q In the DV mode, p ush [MENU] one or more times to
display the “M3” screen (Menu 3).
 •IntheDRmode,p ush [MENU] once or twice to select
the “D1” screen.
w P ush [DSET](F-5) to display the “DSET” screen.
e P ush [SET](F-5) to enter the DV Set mode.
r Push [Y](F-1) or [Z](F-2) to select the desired
item.
t Rotate [MAIN DIAL] to select the desired option.
 •Holddown[F-3] for 1 second to reset to the default set-
ting, if desired.
y Push [MENU] to save, and return to the “DSET”
screen.
Standby Beep 1. (Default: ON-1)
Turn the Standby beep function ON or OFF.
This function sounds a beep when the other station
stops transmitting.
•OFF :TurnsOFFthefunction.
•ON-1 :TurnsONthefunctiontosoundabeep.
•ON-2 :TurnsONthefunctiontosoundabeep.
If the call was sent to your own call sign, the
beep has a higher pitch.
Auto Reply 2. (Default: OFF)
Turn the automatic reply function ON or OFF.
This function automatically replies to a call addressed
to your own call sign, even if you are away from the
transceiver.
This function is automatically turned OFF after you
push [PTT] (microphone) or [TRANSMIT].
•OFF :TurnsOFFthefunction.
•ON  :Thetransceiverautomaticallyrepliestothe
call with your own call sign.
DV Data TX 3. (Default: PTT)
For low-speed data communication, select whether to
transmit the input data manually or automatically.
•PTT :Push[PTT](microphone)or[TRANSMIT]to
manually transmit the input data.
•Auto :WhendataisinputfromaPCthroughthe
[DATA1] jack, the transceiver automatically
transmits it.
Digital Monitor 4. (Default: Auto)
Select the RX monitoring mode by holding down [XFC]
while in the DV mode.
•Auto :
Monitors in the DV mode or FM mode, de-
pending on the received signal.
•Digital :MonitorsintheDVmode.
•Analog:MonitorsintheFMmode.
Digital RPT Set 5. (Default: ON)
Turn the digital repeater setting function ON or OFF.
When accessing a repeater that has a call sign dif-
ferent than the transceiver’s “R1” setting, this function
reads the repeater’s downlink signal and automatically
sets the correct repeater call sign into “R1.”
•OFF :TurnsOFFthefunction.
•ON  :Automaticallysetstherepeatercallsign.
RX Call Sign Write 6. (Default: OFF)
Turn the RX call sign automatic write function ON or
OFF.
When receiving a call addressed to your own call sign,
this function automatically sets the call sign of the call-
ing station into “UR.”
While in the DR mode, this function is disabled.
•OFF :TurnsOFFthefunction.
•Auto :Automaticallysetsthecallsignofthecalling
station into “UR.”
∫ 1 √ ON–1
Standby Beep
SET
Select the item
Reset to the default
setting
Displays the DV Set mode
item name and number
Displays the option
[MAIN DIAL]
[MENU]
[DSET]/[SET][][]