■ GPS Set mode (Continued)
Data Extension20. * (Default: OFF)
Set the data extension capability to “Course/Speed”
or OFF.
When you select “Course/Speed,” the transceiver’s
course and speed information is transmitted along with
the position data.
NOTE: When “Course/Speed” is selected, “Com-
ment (Extension)” appears instead of “Comment,”
and number of characters is limited to 36.
Time Stamp21. * (Default: OFF)
Select either the DHM or HMS format to transmit the
current UTC (Universal Time Coordinated) time as a
time stamp, or turn OFF the function.
•OFF :Doesnottransmitthetimeinformation.
•DHM:TransmitsthetimestampintheDay,Hour,
and Minute format.
•HMS:TransmitsthetimestampintheHour,Minute,
and Second format.
GPS-A Symbol22. *
(Default: House QTH (VHF))
Select the desired GPS-A symbol which represents
your means of transportation.
Selectable symbols:
Ambulance,Bus,FireTruck,Bicycle,Yacht,Helicopter,
Small Aircraft, Ship, Car, Motorcycle, Balloon, Jeep,
RV, Truck, Van, House QTH (VHF) and Other
If there is no symbol you want to use, you can make a
desired symbol code, as described below.
• Symbol programming
q Rotate [MAIN DIAL] to select “Other.”
•[EDT](F-4)andthecurrentsymbolcodeappear.
w Push [EDT](F-4) to enter the programming mode.
•Acursorblinksontherstdigit.
e Rotate [MAIN DIAL] to select the first digit character
to input.
Usable characters: ⁄,\,0to9,AtoZ
r Push [≈](F-3) to select the second digit.
•Acursorblinksontheseconddigit.
t Push [F-1] one or more times to select the desired
character type.
Character
type
Selectable characters
ABC A to Z
abc a to z
etc
!#$%&\?" ’ ` ^ + – ✱⁄.,:;=<>()
[ ] { } ¦ _ ¯ @ (space)
y Rotate [MAIN DIAL] to select the second digit char-
acter to input.
When inputting numbers or a decimal point, push
the appropriate keypad key.
u Push [MENU] to save the symbol code, and return
to the “SET” screen.
When “Other” is selected, check the symbol codes of
APRS
®
, and set them correctly.
SSID23. * (Default: ---)
To assist in identifying a station’s type, the displayed
APRS
®
based SSID is added after the GPS-A data
call sign.
•--- :DoesnotuseanySSID.However,ifyou
use a capital letter, it will be used as an
SSID.
(Example)
JA3YUA➜JA3YUA
JA3YUAA➜JA3YUA-A
•(-0) :NoSSID.Ifyouuseacapitalletter,itwill
be deleted.
(Example)
JA3YUA➜JA3YUA
JA3YUAA➜JA3YUA
•-1to-15 :Adds an SSIDof -1to -15 toyourcall
sign. If you use a capital letter, it will be
replaced with the SSID.
(Example;“-9”isentered)
JA3YUA➜JA3YUA-9
JA3YUAA➜JA3YUA-9
NOTE: If you have multiple transceivers, your call
signs are distinguished by a single capital letter in
the D-STAR* system. When you use an SSID, the
capital letter will be replaced by the SSID, depend-
ing on the setting.
*
Appears when “GPS-A” is selected in “GPS TX Mode.”
To Next Page
Loading...
Need help?
General
