ID Lock 150 - Page 43

Side 43
English All Functions Quick Reference Guide
Settings
Relocking on/off
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [2] [*] to enter settings menu
4 Access relocking by pressing [8]
5 Press [0] for relocking off
6 Press [1] for relocking on
Settings
Automatic/manual locking
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [2] [*] to enter settings menu
4 Press [6] for automatic locking
5 Press [4] for manual locking
Settings
Volume increase/decrease
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [2] [*] to enter settings menu
4 Press [1] for volume increase
5 Press [3] for volume decrease
6 Save settings with [#]
Default Settings
Master PIN: 1234
Hinge direction: Right
Relocking: On
Lock Mode: Automatic
Service PIN mode
[1]: 1 time use
[2]: 2 times use
[3]: 3 times use
[4]: 5 times use
[5]: 10 times use
[8]: Valid 12 hours
[9]: Valid 24 hours
Register
Service PIN
1 Close and lock the door
2 Touch the panel
3 Press [*] [Master PIN] [*]
4 Press [2] [*]
5 Enter [new Service PIN] [*]
6 Enter [service PIN mode]
Delete user PIN
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [1] [*] to enter access menu
4 Press [4] [*]
5 Choose index [1-9] or [0] for alle [#]
Add new user PIN
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [1] [*] to enter access menu
4 Press [3]
5 Choose index [1-9] [*]
6 Enter [new user PIN] [#]
Add/delete RFID keyfob
1 Press and hold key button
2 Enter [Master PIN] [*]
3 Press [1] [*] to enter access menu
4 Press [6] (add) or [7] (delete),
5 Choose index [1-9], or [0] for all [#]
(0 can only be used when deleting)
Settings
Z-Wave Local Reset
1 Put GW/Hub in exclusion mode
2 Press and hold key button on ID Lock
3 Enter [Master PIN] [*]
4 Press [2] [*] for settings menu
5 Press [5]
Settings
Z-Wave Exclusion
1 Put GW/Hub in exclusion mode
2 Press and hold key button on ID Lock
3 Enter [Master PIN] [*]
4 Press [2] [*] for settings menu
5 Press [5]
Settings
Z-Wave Inclusion
1 Put GW/Hub in inclusion mode
2 Press and hold key button on ID Lock
3 Enter [Master PIN] [*]
4 Press [2] [*] for settings menu
5 Press [5]
Reset burglar alarm
1 Touch the panel
2 Enter [valid PIN] [#]
Reset to factory settings
1 Remove all batteries
2 Insert the batteries one by one
3 When the fourth battery is inserted, press
and hold the key button until a receipt
tone is heard
Activate/deactivate away mode
1 Close and lock the door
2 Touch the panel
3 Enter [valid PIN] followed by [*]
Away mode is deactivated when the
door is unlocked.
Unlock with RFID
LOCK IS OPERATED FROM THE OUTSIDE
1 Touch the panel
2 Present valid RFID keyfob
Open with PIN
LOCK IS OPERATED FROM THE OUTSIDE
1 Touch the panel
2 Enter [valid PIN] [#]
Manual locking
LOCK IS OPERATED FROM THE OUTSIDE
1 Close the door
2 Touch the panel
Register new Master PIN
1 Press key button
2 Enter [Master-PIN] [*]
3 Press [1] [*] to enter access menu
4 Press [1] [*]
5 Enter [new Master PIN] [*]
6 Repeat [new Master PIN] [#]
Set hinge direction
1 Press key button
2 Enter [Master PIN] [*]
3 Press [2] [*] for settings menu
4 Press [9] for -right hinged door
5 Press [7] for -left hinged door
Important!
The door’s hinge direction must be pro-
grammed immediately after installation.
The lock will not function as intended if
the correct hinge direction is not set.