(2) Multi SDI input module
· DKM-5018 (Multi SDI module) [standard]
· DKM-501A(Multi SDI module)
Equipped with x/sin x coITection type
high-performance video signal post filter
· DKM-501AAV/BAV
(Multi-SDI module compatible with embedded analog audio output)
· DKM-501AAVD/BAVD
(Multi-SDI rnodulecornpatiblewithembeddedAES/EBU audio output)
Video system
1. Input/Output terminal
Input: BNC 2-lines
Output: BNC I-line (Only one selected output is active loop-through.)
2. Input signal format (HD/SD auto recognition)
a) HD-SDI
1035i/60, 59.94
• 1080i/60, 59.94
• 720p/60, 59.94 (Type-I only)
b) SD-SDI (4:2:2)
525i/59.94
• 625i/50
3. Input Level Rating
4. Transmission Speed
a) HD-SDI:
b) SD-SDI (4:2:2):
5. Quantifying Bit Number
800mVp-p± 10%
l.485Gb/s
270Mb/s
6. Input/Output impedance
10 bits
750
7. Return loss
Audio system
Above 15d8 (~742.5MHz)
Above IOdB (742.5~1485MHz)
Common to embedded audio specifications
1. Format corresponding to embedded audio input
SMJYfE272M: 480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMJYfE299M: I 035i/60, 59.94
1080i/60, 59.94
1080i/50
1080i/48, 47.95
720p/60, 59.94
2.FormatChange
Automatic Change
3. Sampling Frequency 48kHz(Synchronized with video lock)
HTM-1505R/HTM-1505CS
Analog Audio Output (AV type)
* Analog audio level: Od8s=-0.775V1ms
1. Output Terminal
XLR-5-32 (Canon 5-pin, Male)
2. Line-out
Analog audio 2 channels
Active (transformerless) balance type
3. Rated Output Level + 4dBs * Load-impedance IOI&
(At the time of digital audio level: -20dBFS)
4. Maximum Output Level
+ 24dBs * Load-impedance I Ok.O.
(At the time of digital audio level: OdBFS)
5. Output-Impedance 50 0
6. Minimum Load Impedance 600 0
7. Quntuifying Bit Number
8. Emphasis
9. Frequency Characteristic
10. Signal-to-Noise Ratio
11. Dynamic Range
12. Cross Talk
13. Total Harmonic Distortion
24bits/ch
50115 µ s digital emphasis
(Automatic discrimination)
20~20kHz± !dB
Above80dB
Above80dB
Above60dB
( I KHz at maximum output)
Above0.1%
(At the time ofrated output)
AES/EBU Output System (AVD Type)
* Digital audio level: OdBFS foll bit/li.11I scale
1. Output Connector BNC (Pair Channel) 4 lines
2. Output Standard AES/EBU Standard (for monitor)
3. Output Impedance 75 0
(3) SD-SDI input module (Option)
· DK-801(4:2:2 digital component module)
* Not coITesponding to embedded audio.
1. Input/Output Terminal
BNC 2 lines (Active loop-through)
* Signals interlocked with a channel selected on the monitor side
are output according to settings in the module.
2. Input Signal Format
4: 2: 2 digital component signal (525i/59.94, 625i/50)
3. Input/Output Level
Rating: 800mVp-p±IO%
(Output level at the time of75Q tennination)
SCRAMBLED NRZI type
4. Transmitting Speed 270Mb/s
5. Quantitying Bit Number !Obits
. 6. Output Impedance
7. Return loss
750
Above 15dB (~270MHz)
5
To Next Page
Loading...
