innomar SES smart - Page 9

User’s Manual Innomar SES Parametric Sub-bottom Profilers 9
Innomar Technologie GmbH (2020-09) 9
6.8 How to use the Broadcast Server to display data on HYPACK
®
.................................. 104
6.9 How to use SESWIN’s documentation and report tools ............................................... 107
6.9.1 Document SESWIN system and interface settings ............................................ 107
6.9.2 Log files for work reports / profile lists ................................................................ 107
6.9.3 System information and LOG files for troubleshooting ....................................... 108
6.10 How to reset to factory defaults ................................................................................... 108
6.11 How to remote-control an Innomar SBP ...................................................................... 109
6.11.1 Operating the Innomar system via KVM extender.............................................. 109
6.11.2 Operating the Innomar system via RS232/Ethernet connection ......................... 109
7 Maintenance and Error Handling ................................................... 111
7.1 Hardware Handling and Maintenance .......................................................................... 112
7.1.1 Transducer ........................................................................................................ 112
7.1.2 Transducer Visual Inspection ............................................................................ 112
7.1.3 Hull-mounted Transducers ................................................................................ 113
7.1.4 Topside Unit Handling ....................................................................................... 113
7.1.5 Topside Unit Maintenance ................................................................................. 113
7.1.6 System-Check ................................................................................................... 114
7.2 Hardware Related Issues ............................................................................................ 115
7.2.1 The voltage indicators (LEDs) at the front panel are not illuminated .................. 115
7.2.2 The internal display is switched off if an external monitor is connected ............. 115
7.2.3 The internal display is white. The PC seems not to boot. ................................... 115
7.3 SESWIN Error Messages at System Start ................................................................... 116
7.4 SESWIN Error and Warning Messages at System Setup ............................................ 118
7.5 Other SESWIN Error and Warning Messages ............................................................. 120
7.6 No incoming sensor data ............................................................................................. 122
7.6.1 No data or instable from the Motion Sensor ....................................................... 122
7.6.2 No incoming position data ................................................................................. 122
7.7 SESWIN functions seem not to work ........................................................................... 123
7.7.1 Transmitters can’t be switched on ..................................................................... 123
7.7.2 Changing the “Range” is impossible .................................................................. 123
7.7.3 Data-Recording is not possible .......................................................................... 123
7.7.4 The Output “Depth Out” does not work .............................................................. 123
7.8 Signal detection problems ........................................................................................... 124
7.8.1 No seafloor on the screen ................................................................................. 124
7.8.2 The echo signal is too small .............................................................................. 124
7.9 Firmware Update ......................................................................................................... 125
8 SES NetViewer Software ................................................................. 127
9 SES Convert Software .................................................................... 129
9.1 Example data at Innomar’s ISE post-processing software ........................................... 129
9.2 Convert Innomar data into SEG-Y format using SESCONVERT .................................. 130
9.2.1 SEG-Y Conversion Settings .............................................................................. 131
9.2.2 SEG-Y Processing Settings ............................................................................... 132
9.2.3 Data Conversion................................................................................................ 133
9.3 Checking the SEG-Y files ............................................................................................ 134
9.4 Store / Reload Conversion Settings ............................................................................. 134
10 ISE Post-Processing Software ....................................................... 135
11 Data Acquisition and Post-Processing Workflow ......................... 137
11.1 Survey preparation and survey line planning ............................................................... 137
11.2 System setup and mobilisation .................................................................................... 137
11.3 Data acquisition ........................................................................................................... 139
11.4 Data Acquisition: Example Settings ............................................................................. 141
11.5 Data Quality Check (Innomar ISE Software) ................................................................ 142