Why does the TIG electrode melt when I strike an arc with my Jasic TIG Welding System?
If the TIG electrode melts when the arc is struck on your Jasic Welding System, it's likely that the TIG torch is connected to the (+) VE terminal. Reconnect the TIG torch to the correct terminal.
What causes excessive spatter in MMA welding with my Jasic TIG Welding System?
If you observe excessive spatter during MMA welding with your Jasic Welding System, the output polarity connection may be incorrect. Exchange the polarity connection.
Why does the electrode holder get so hot on my Jasic TIG Welding System?
If the electrode holder becomes very hot when using your Jasic Welding System, it is because the rated current of the electrode holder is smaller than its actual working current. Replace it with a higher rated current capacity electrode holder.
Why does the welding current decrease while welding with my Jasic TIG?
If you notice the welding current reduces while welding with your Jasic Welding System, it could be due to a poor work lead connection to the workpiece. Check and secure the work lead connection.
Why is my Jasic TIG Welding System not producing high frequency?
If your Jasic Welding System is not producing high frequency, it could be due to several reasons. First, check if the process selection switch is set to manual metal arc (MMA); if so, change it to a different mode. Second, ensure the torch trigger switch lead is connected and not faulty; reconnect or replace if necessary. Finally, inspect the high frequency spark gap; adjust if it's too wide or short-circuited.
What does error E13 mean on my Jasic Welding System?
If your Jasic Welding System displays 'E13 - Current feedback is abnormal', power off the machine and check the connection of the current feedback line. Contact the service department for assistance if the problem persists.
What does error E33 mean on my Jasic TIG Welding System?
If your Jasic Welding System displays 'E33 - Voltage feedback is abnormal', power off the machine and check the connection of the voltage feedback line. Contact the service department for assistance if the problem persists.
What to do if the Jasic Welding System fault LED is ON and the fan is running?
If the fault LED is illuminated and the fan is operational on your Jasic Welding System, it could be due to overheating protection. Allow the machine to cool down. Also, verify the incoming mains supply voltage to ensure it is within 230V +/- 15%.
What to do if welding current reduces when welding with Jasic Welding System?
If the welding current reduces while welding with your Jasic Welding System, it could be due to a poor work lead connection to the work piece. Ensure a proper connection of the work lead to the work piece.
How to fix no high frequency produced by Jasic Welding System?
If your Jasic Welding System is not producing high frequency, check the following: * The process select switch may be set to manual metal arc (MMA). Set the process select switch to the appropriate setting. * The torch trigger switch lead may be disconnected or faulty. Reconnect or replace the faulty torch trigger switch lead. * The high-frequency spark gap may be too wide or short-circuited. Adjust the high-frequency spark gap.
General| Output Current Range | 10-200A |
|---|---|
| Welding Type | TIG |
| Frequency | 50/60 Hz |
| Protection Class | IP21S |
| Insulation Class | F |
| Duty Cycle | 60% |
Covers safety precautions related to electrical connections, grounding, and avoiding live parts.
Provides guidelines for safe operation, handling, and use in hazardous environments.
Details essential protective gear like helmets, glasses, clothing, gloves, and footwear for welding.
Guides on connecting the power supply and output terminals for MMA and TIG welding.
Step-by-step guide to connecting electrode holder and work return lead for MMA welding.
Instructions for connecting the TIG torch, work clamp, and gas hose for TIG welding.
Explains MMA welding, shielding from flux, and weld bead formation.
Steps to select MMA mode, check output, and use VRD indicator and current adjustment.
Details on setting welding current, hot start, and arc force for optimal MMA results.
Explains TIG welding, process types (DC/AC), and connection of torch, work clamp, and gas.
Guides on selecting DC TIG mode, 2T operation, and adjusting Pre-flow, Initial Current, and Upslope time.
Details on setting downslope time, final current, and post-flow gas time for TIG welding.
Lists common MMA welding defects, their possible causes, and recommended actions for prevention.
Explains DC welding principles, electrode negative setup, and heat distribution for penetration.
A step-by-step guide for basic DC TIG welding setup, including parameter settings.
Provides recommended settings for Pre-gas time, Start Current, Upslope time, Peak current, etc.
Identifies common TIG welding defects, their causes, and corrective actions.
Addresses specific TIG welding problems like bead build-up, penetration, and tungsten melting with solutions.
Outlines daily, monthly, and yearly maintenance tasks and provides a record for service history.
Lists common operational faults, their potential causes, and recommended user actions.
Explains various error codes, their categories, symptoms, causes, and user-implemented measures.
To Next Page
